Fingerprint

F7_F707_F708 Installation Instruction V1.0

F7_F707_F708
Access Control Terminal
Installation Instructions

Revised May 2008 About this Guide This guide provides installation instructions only. For information regarding actual operation and configuration of the F7_F707_F708 Time & Attendance and Access Control Terminal, refer to the user manual.

-1-

F7_F707_F708 InstallationInstruction V1.0

Table of Contents
Before Installation ................................................................................. 1 Front and Read Panel views ………………………………………….5 Optional 3rd Party Equipment………………………………………..6 1.0 Installation........................................................................................ 7 1.1 Attaching Mounting Plate……………………………………..7 1.2 ConnectingPower Supply……………………………………. 9 1.3 Selecting Door Lock………………………………………… 10 1.4 Connecting an electric strike or magnetic lock……………... 11 1.5 Powering Door Lock………………………………………... 13 1.6 Connecting switches, door sensor, doorbell, etc……………..14 1.7 Connecting 3rd party door controller/panel…………………..16 1.8 Connecting network or computer…………………………….17 2.0 Testing……………………………………………………………..20 2.1 Run AutoTest………………………………………………...20 2.2 Test Fingerprint Enrollment………………………………….23 3.0 Fastening to mounting plate and wall…………………………..30 4.0 Miscellaneous……………………………………………………..31 5.0 Trouble-shooting………………………………………………...32

-2-

F7_F707_F708 Installation Instruction V1.0

Before Installation
1. Prior to beginning installation, cut off all power to prevent personal injury and damage to the F7_F707_F708and peripheral equipment. 2. Connect the ground wire first, in order to prevent electro-static damage to the F7_F707_F708. 3. Connect 12V DC power supply to the F7_F707_F708 last. If the F7_F707_F708 does not operate properly, always cut off power to it before examining/dismantling. Be advised that wiring the F7_F707_F708 while power is on may cause damage to the terminal. Possible resulting damagefrom not powering off the F7_F707_F708 prior to wiring is not covered by manufacturer’s warranty. 4. Mount the F7_F707_F708 at a comfortable height, typically between 4 and 5 feet from the ground. 5. After installation, remove protective film from the F7_F707_F708 display and fingerprint sensor. 6. To prevent being accidentally locked out while testing the exit-door button, keep a person on theinside of the door.

7. Run the auto-test function to confirm that installation is successful.
-3-

F7_F707_F708 Installation Instruction V1.0

8. In order to maximize the life of the F7_F707_F708, use the auto-sleep and wake up functions. 9. ONLY use a 12V DC 1.5Amp power supply for proper functioning of the F7_F707_F708 terminal. If the incorrect voltage is used, the F7_F707_F708 may keeprebooting or may not operate the electric door lock (if attached). 10. Improper wiring may cause the F7_F707_F708’s main circuit board and fingerprint sensor to burn out. Resulting damage from improper wiring is not covered under manufacturer’s warranty. 11. Only use supplied transformer and cord. Do not attempt extending the cord by cutting and splicing. 12. If using RS485 mode of communication,use only a ZK Software-supplied RS485 converters. Using a 3rd party RS485 converter may or may not work. If the RS485 cable length exceeds 200 feet, we recommend using a 120Ώ terminator. 13. Refer to the user handbook and operating instructions for further information.

-4-

F7_F707_F708 Installation Instruction V1.0

Front panel view;

Rear panel view;

-5-

F7_F707_F708Installation Instruction V1.0

Optional 3rd party equipment
The following equipment is not provided by ZK Software, but often compliments a complete Access Control solution; Part PC Image Part Door Lock Image

Door sensor

Exit Button

Alarm

RS485/ RS232 converter

Door Controller

Network Cable

-6-

F7_F707_F708 Installation Instruction V1.0

1.0 Installation

1.1 Attach...