Las Canicas

Rev. 090302
AL1012ULX Series
Power Supply/Charger
Installation Guide
Models Include:
•AL1012ULX
- Single Output
• AL1012ULXPD4 • AL1012ULXPD4CB
- Four (4) Fused Outputs - Four (4) PTC Outputs
• AL1012ULXPD8 • AL1012ULXPD8CB
- Eight (8) Fused Outputs - Eight (8) PTC Outputs
• AL1012ULXPD16 • AL1012ULXPD16CB
- Sixteen (16) Fused Outputs - Sixteen (16) PTC Outputs
- 2 - AL1012ULXseriesOverview:
The AL1012ULX is a power supply that converts a 115VAC / 60Hz input, to a 12VDC output (see specifications).
The AL1012ULX is a base unit for a series of UL Listed multi-output power supply/chargers, including:
AL1012ULXPD4, AL1012ULXPD4CB, AL1012ULXPD8, AL1012ULXPD8CB, AL1012ULXPD16,
AL1012ULXPD16CB (Refer to AL1012ULX Series Power Supply Configuration Reference Chart).
AL1012ULXSeries Power Supply Configuration Reference Chart:
Input:
• Input 115VAC / 60Hz, 1.9 amp.
• AC input and DC output LED indicators.
Output:
• 12VDC output.
• 10 amp total supply current at 12VDC.
• Filtered and electronically regulated outputs.
• Short circuit and thermal overload protection.
Battery Backup:
• Maximum charge current .7 amp.
• Built-in charger for sealed lead acid or
geltype batteries.
Battery Backup (cont’d):
• Automatic switch over to stand-by battery when
AC fails.
• Zero voltage drop when switched over to
battery backup.
Supervision:
• AC fail supervision (form "C" contacts).
• Battery presence and low battery supervision
(form “C” contacts).
Added Features:
• Power supply, enclosure, cam lock and battery leads.
Specifications:
AL1012ULX - 1 - -- 10
AL1012ULXPD4 PD4UL 4 - x - 3.5
AL1012ULXPD4CB PD4ULCB 4 x - x 2.5
AL1012ULXPD8 PD8UL 8 - x - 3.5
AL1012ULXPD8CB PD8ULCB 8 x - x 2.5
AL1012ULXPD16 PD8UL 16 - x - 3.5
AL1012ULXPD16CB PD8ULCB 16 x - x 2.5
UL 294
(File # BP6714)
UL Listed for
Access Control
Systems.
“Signal Equipment”
Evaluated to
CSA Standard
C22.2
No.205-M1983
Altronix
Model Number
Accessory PowerDistribution
Module(s)
Number of Outputs
Fused Outputs
PTC Outputs
Agency Lisitings
UL Listings and
File Numbers
Class 2 Rated
Power Limited Outputs
Output Rating (amp)
per Output
AL1012ULXseries - 3 -
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local
codes and authorities having jurisdiction. Productis intended for indoor use only.
1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drillthe lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 8).
Secure enclosure to earth ground.
2. Connect AC power (115VAC / 60 Hz to terminals marked [L, G, N] (Fig. 1, pg. 5). Use 14 AWG or larger for all
power connections (Battery, DC output, ACinput). Use 22 AWG to 18 AWG for power limited circuits (AC Fail/
Low Battery reporting). Keep power limited wiring separate from non-power limited wiring (115VAC / 60Hz Input,
Battery Wires). Minimum .25” spacing must be provided.
3. Measure output voltage before connecting device. This helps avoid potential damage.
4. Connect devices to be powered:
a. For Power Supply Board connect toterminals marked [+ DC -] (Fig. 1, pg. 5).
b. For Power Distribution Module(s) connect devices to be powered to terminal pairs 1 to 4 marked
[1P & 1N thru 4P & 4N] (Fig. 2, pg. 6) or 1 to 8 marked [1P & 1N thru 8P & 8N] (Fig. 3, pg. 6) carefully
observing correct polarity.
When servicing the unit, AC mains should be removed.
5. For Access Control applications, batteries are optional. When...