Mstatus

TRACK 1, 2 (2, 3) DIP MSR

M_STATUS Meaning
00 No error
01 Blank track
02 Track not supported
03 Read error (Parity LRC no end sentinel)
05 No data available
146 SDC link failure

MCR/MCRW

M_STATUS Meaning
00 No error
01 Blank track
02 Track not supported
03 Read error
04 Write error
05 No card in reader at start of command
06 Card removed by customer during capture
07Shutter jammed open
08 Shutter switch failure detected
09 Error recovery successful
10 Shutter jammed closed
11 Card jam
12 Card captured after unsuccessful eject
13 Possible customer tampering
14 Too many consecutive read errors or blank tracks on any track
15 Too many consecutive write errors
16 Too many consecutive card jams
17 Too many consecutive shutter jammed closed
18 Card jam duringcapture
19 Too many consecutive invalid cards
20 Device still inoperative
21 No card entered during cleaning cycle test
22 Speed out of specification fast
23 Speed within +3%
24 Speed within +/-1%
25 Speed within -3%
26 Speed out of specification slow
27 Invalid card detected (diagnostic only)
37 CROPF feature not supported
38 LFCC bin full soon/full
39 LFCC bin shutter mechanism fail40 LFCC bin removed/not configured
41 CROPF feature failure
146 SDC link failure

SMART CARD READER/WRITER
M_STATUS Meaning
50 Card not in SCRW stage position
51 Smart card stopper pin lowered, unable
to capture. This is only in response to
card capture
52 Invalid smart card command code error
53 Invalid smart card command data
error
54 SCIF not configured/not responding
55 SCIFresponse timeout exceeded
56 Not in MCRW mode
57 Invalid smart card response length

Additional M_STATUS codes may be returned by the
SCIF as shown in the following table

M_STATUS Meaning
00 Good
64 Invalid command code
65 Invalid command format
67 Invalid key ID
68 Invalid key type
69 Invalid host key type
70 Invalid key - does not exist
71 Invalid password - not decimal
72 Invalidpassword - no match
73 Key integrity error
74 Key parity error
75 Invalid data format
76 Stopper pin failure
77 Contact unit failure
78 Card movement failure
79 SC switch off failure
80 Smart card removed error
81 No smart card response
82 Smart card transmission error
83 Smart card switched off
84 Illegal card type/parameter
85 Power up time exceeded
86 ANSI X9.8 pin block errorCARD IDENTIFICATION MODULE (CIM86)
M_STATUS Meaning
00 No error
01 Blank track
02 Track not supported
03 Read error
04 Write error
05 No card in reader at start of command
06 Card removed by customer during
capture
07 Shutter jammed open
08 Shutter switch failure detected.
09 Error recovery successful
10 Shutter jammed closed
11 Card jam
12 Card captured after unsuccessful eject
13Possible customer tampering
14 Too many consecutive read errors or
blank tracks on any track
15 Too many consecutive write errors
16 Too many consecutive card jams
17 Too many consecutive shutter jammed
closed
18 Card jam during capture
19 Too many invalid cards
20 Device still inoperative
21 No card entered during cleaning cycle
test
22 Speed out of specification fast
23 Speedwithin +3%
24 Speed within +/-1%
25 Speed within -3%
26 Speed out of specification slow
27 Invalid card detected (diagnostic only)
33 CIM service test failed
35 Error in track 3 data
37 CROPF feature not supported
38 LFCC bin full soon/full
40 LFCC bin removed/not configured
41 CROPF feature failure
87 CIM self test failed
88 CIM security module defective
89 CIM security modulecommunications
failure
90 CIM Interface pcb defective
91 CIM Interface pcb communications
Failure

USB EPP

M_STATUS Meaning
0 Good
06 Security Module reset was successful
07 Security Module reset was unsuccessful

ENCRYPTOR

M_STATUS Meaning
00 Good
01 Parity Error or Invalid Command
02 Hardware error
03 Invalid command as not all key spaces are closed
04 Invalid command no key space...