Tecnico Electromecanico

1

Manual for Remote View & Control-Router UPNP Supported

H.264 Network Embedded DVR
INSTRUCTION MANUAL FOR REMOTE VIEW&CONTROL ---------------- Router UPNP Supported----------------

Visionari Limited Liability Company http://www.mydepots.com

Visionari Copyright(1.5)2010Version

2

Manual for Remote View & Control-Router UPNP Supported

Content
Zone A: Setting on DVR interface       Step 1: Plug network line into DVR’s LAN…………………………………………………P3 Step 2~4: Coming into DVR’s network setting interface………..……………………….P3~4 Step 4-1: Setting for 【TYPE】…………………………………………………………….P4 Step 4-1-1~4-1-2: Getting clues for 【IP Addr】&【AUTO DHCP】…………………..P5 Step 4-2: Setting for 【MEDIA PORT】&【WEB PORT】………………………………..P5 Step 4-3: Finding out【DNS】IP………………………………………………………..…..P6 Step4-4: Restarting DVR system after setting………………………………………………P6

Zone B: Setting on your router    Step 4-5~4-6: Setting on your router…………….. …………………………………………P7 Step 4-7: Checking 【UPNP】status……………………………………………………..…P7 Step 4-8: Methods to Visit DVR…………………….. …………………………………..….P8

Zone C: Setting on remote view interface         Step 4-8-1~4-8-3: How to visit DVR through WANIP…………………...………….…P8~9 Step 4-9~4-9-4: How to set【DDNS】on DVR interface……………………………….P9~10 Step 4-9-5~4-9-15: How to register for【DDNS】……………………………………. P11~15 Step 4-9-16: Filling 【DDNS】registered clues on DVR interface……………….….……P16 Step 4-9-17~4-9-18: How to visit DVR through 【DDNS】………………………… P16~17 Step 4-9-19: Final scene when Realizing remote view ………………………….…….. P17 Step 5: Setting on remote viewinterface………………………………………………. P18 Step 6~6-1: Setting visiting password on remote view interface……………….......P18

Attention here: all data below is cited from writer’s local network situation (system fault parameter is exception), please adjust according to your actual environment.

Visionari Limited Liability Company http://www.mydepots.com

Visionari Copyright(1.5)2010Version

3

Manual for Remote View & Control-Router UPNP Supported

Zone A:Setting on DVR interface Step 1: Plug network cable line into LAN, assure the light is on, indicating network is normal. Figure (1)



Figure 1 Step 2：Coming into DVR’s main menu, select 【ADVANCE】 ，Press【Enter】



Figure 2 Step 3：select 【NETWORK】, Press【Enter】

Figure 3

Visionari Limited Liability Company http://www.mydepots.com

Visionari Copyright(1.5)2010Version

4

Manualfor Remote View & Control-Router UPNP Supported



Step 4: You’ll find interface as below and you need fill them accordingly.

Figure 4

 Step 4-1: 【TYPE】: Here’re 3 options, you need firstly check whether your router support “UPNP”, if yes, please select it and follow next steps(if not, please get reference from another manual under 【STATIC】mode)

Figure 4-1

Visionari LimitedLiability Company http://www.mydepots.com

Visionari Copyright(1.5)2010Version

5

Manual for Remote View & Control-Router UPNP Supported

 Step 4-1-1: when set 【TYPE】 【DHCP】 at the same time you need set 【UPNP】 as , as 【OPEN】, in this way, immediately, DVR system will automatically obtain 【IP Addr】 and 【AUTO DHCP】like below,Attention here: 【IP Addr】: Refers to DVR IP address 【AUTO DHCP】:Refers to DNS IP address

Figure 4-1-1



Step 4-1-2: After short while, you’ll find interface result as below:

Figure 4-1-2  Step 4-2: 【MEDIA PORT】: It’s for video transmission via IE, please keep it as default. 【WEB PORT:】: It means “set up the port of IE browser via HTTP”，please input any port number(But please don’t use system default port 00080, it’s a must to change another), providedthat it’s a 5-digit number and not used by any other device in your wireless environment, i. e, here assumed we set it as 【09001】.

Visionari Limited Liability Company http://www.mydepots.com

Visionari Copyright(1.5)2010Version

6

Manual for Remote View & Control-Router UPNP Supported

 Step 4-3: 【DNS】: you need fill local DNS...