Manual inverter fuling ingles

velocity

INTERNATIONAL QUALITY SYSTEM AUTHENTICATION ENTERPRISES

TABLE OF CONTENTS

Preface
Chapter 1 Introduction Chapter 2 Installation and Wiring Chapter 3 Digital Keypad Operation Chapter 4 Start Up Chapter 5 Summary of Parameter Settings Chapter 6 Parameter Settings Chapter 7 Troubleshooting and Fault information Chapter 8 Quality Guarantee Appendix A Standard SpecificationsAppendix B Dimensions

DZB100H Series

Preface

Preface
Thank you for choosing D Z B 1 0 0 Series high-performance AC Motor Drives. D Z B 1 0 0 Series are manufactured by adopting high-quality components, material and incorporating the latest microprocessor technology available. Getting Started This manual will be helpful in the installation, parameter setting, troubleshooting, and dailymaintenance of the AC motor drives. To guarantee safe operation of the equipment, read the following safety guidelines before connecting power to the AC drives. Keep this operating manual handy and distribute to all users for reference.

! WARNING
AT T E N T I O N : Always read this manual thoroughly before using D Z B 1 0 0 series AC Motor Drives. DANGER! AC input power must be disconnected beforeany maintenance. WARNING! Do not connect or disconnect wires and connectors while power is applied to the circuit. Maintenance must be performed by qualified technicians. WARNING! To avoid personal injury, do not remove the cover of the AC motor drive until all of thedigital keypad "DISPLAY LED" lamps are off. The DC-link capacitor remains charged with a hazardous voltage even after input power isremoved. AT T E N T I O N : Grounding the DZB100B drive is done by c o n n ec t i n g t h e E a r t h G r o u n d t o t h e drive ground terminal . CAUTION: There are highly sensitive components on the printed circuit boards. These components a r e e s p e c i a l l y s e n s i t i v e t o E S D ( e l e c t r o s t a t i c d i s c h arg e ) . To avoid damage to the drive , do not touch componentsor the circuit boards until static control precautions have been taken. CAUTION: Never connect the main circuit output terminals U, V, and W directly to the AC main c i rc u i t p o w e r s u p p l y a s this will damage the drive . CAUTION: Do not apply the antirust to screws for fastening drives; Please clean the drives and screws with dry cloth or alcohol, not with synthetic cleaner. Fasten thescrews with washers and rated torque lest the enclosure corners of drives be distorted. This manual is for DZB100H Series AC Motor Drive.

-1-

Introduction

Chapter 1 Introduction
The purpose of this chapter is to provide specific, yet simple information to unpack , install the AC drive. This chapter contains information on the following: 1.1 Receiving, Transportation, and Storage 1.2Nameplate Information

1.1 Receiving, Storage and Transportation
The AC motor drive has gone through rigorous quality control tests at the factory before shipment. After receiving the AC drive, check for the following. Receiving 1.Check to make sure that the package includes an AC drive,the User Manual,dust covers and rubber bushings. 2.Inspect the unit to insure it was not damaged duringshipment. 3.Make sure that the part number indicated on the nameplate corresponds with the part number of your order. Storage The AC Drive should be kept in the shipping carton before installation. In order to retain the warranty coverage, the AC drive should be stored properly when it is not to be used for an extended period of time. Some storage suggestions are: 1.Store in a clean, dry location. 2.Storewithin an ambient temperature range of -20 C to +65 95%, non-condensing. 4.Do not store the AC drive in places where it could be exposed to corrosive gases. 5.Do not store the AC drive on a shelf or on an unstable surface. Transportation Temperature: -25 C to +70 C; R.H.: 0% to 95%; Air Pressure: 70kPa to 106kPa. C. 3.If possible, store in an air-conditioned environment where the relative...