Adm y Configuracion

STM-1 = 8000 * (270 octetos * 9 filas * 8 bits)= 155 Mbps
STM-4 = 4 * 8000 * (270 octetos * 9 filas * 8 bits)= 622 Mbps
STM-16 = 16 * 8000 * (270 octetos * 9 filas * 8 bits)= 2.5 Gbps
STM-64 = 64 * 8000 * (270 octetos * 9 filas * 8 bits)= 10 Gbps
STM-256 = 256 * 8000 * (270 octetos * 9 filas * 8 bits)= 40 Gbps
NODO COMPACTO ADM
ADMs Compactos: Equipamiento |
Puertos | Cantidad |E1s | 63 |
Fast Ethernet 10/100 | 8 |
Gigabit Ethernet | 2 |
STM1 eléctrico | 3 |
STM1 L1.1o L1.3 | 2 |
STM1 S1.1 Conf. 1+1 MSP | 2 |

Área de acceso:
E1:
21X2MB/S PORT 75OHM 1.0/2.3, 3AL78831AA** (3: 1,2,3): Slot position: 1 to 9 - 13 to 21. CONNECTION MODULE
LEGENDA:
– (1) to (21) #1 to #21 2 Mbit/s data signals
– (22) Bicolor LED:
• Red LED = Local unit alarm (INT)
• GreenLED = In-Service unit

4XSTM-1 EL.75OHM
3AL78835AA**, (1: 6), electrical access card: Slot position: 2 to 9 - 13 to 20. CONNECTION MODULE

LEGENDA:
– (1) Channel #1
– (2) Channel #2
– (3) Channel #3
– (4) Channel #4
– (5) Bicolor LED:
• Red LED = Local unit alarm (INT)
• Green LED = In-Service unit

HIGH SPEED PROT. DVBASI

3AL36510AA**, Slot position: 2 to 9 - 13 to 20, (2: 7,17)give EPS (1+1) protection: 4 HF line couples from port to access and 4 HF line couples from access to port realize the protection.

CONTROL AND GENERAL I/F (2 WIRES / 960W / 25A / WITH FAN SUPERVISION) |

CONGI A card. 3AL78830AE** Slot position: 10 and 12 CONGI A main (slot 10) and CONGI B (slot 12). Both units are necessary to provide the complete set. CONGI A can be used as stand alonebut in this case only a subset of interfaces can be used.

LEGENDA:
– (1) Power connector.
– (2) Housekeeping and remote alarms
– (3) Rack lamps (not used on CONGI in slot 12).
– (4) QMD - Q2 (not used on CONGI in slot 12).
– (5) I/O BNC for Q3 10base2 (not used on CONGI in slot 12).
– (6) RJ45 for Q3 10baseT (not used on CONGI in slot 12).
– (7) Bicolor LED:
• Red LED = Local unit alarm(INT)
• Green LED = In-Service unit

SERVICE card
SERVICES I/F, 3AL78817AA**, Slot position: 11
LEGENDA
ON : LED on fixed
-- : LED off
F : LED flashing
LEGENDA:
– (1) • I/O auxiliary 2 Mbit/s channels G.703.
–J1 - 2 Mbit/s Channel Output 1
–J2 - 2 Mbit/s Channel Input 1
–J5 - 2 Mbit/s Channel Output 2
–J6 - 2 Mbit/s Channel Input 2
• I/O 2 MHz Synchronousinterfaces
–J3 - 2 MHz Output 1 (T4A) or 2 MHz Output (T5A)
–J4 - 2 MHz Input 1 (T3A) or 2 MHz Input (T6A)
–J7 - 2 MHz Output 2 (T4B) or 2 MHz Output (T5B)
–J8 -2 MHz Input 2 (T3B) or 2 MHz Input (T6B)
– (2) AUX Auxiliary channels
• 4 channels RS-232
• 4 channels V.11 64 kbit/s
• 4 channels G.703 64 kbit/s
– (3) PHONE Ext. 1 4-Wire telephone extension point (RJ45).Note: Not present for 3AL78817 AB.
– (4) PHONE Ext. 2 4-Wire telephone extension point (RJ11). Note: Not present for 3AL 78817 AB.
– (5) Z1 to Z8 EOW zone selection. Note: Only one Zone is operative.
– (6) L1-L2 LEDs status for selective call. Note: For details see.
– (7) Telephone jack.
– (8) Line seizure key.
– (9) ZSEL EOW zone selection. Note: Only one Zone is operative.
– (10) R Reset command key.
– (11)Bicolor LED:
– Red LED = Local unit alarm (INT)
– Green LED = In-Service unit

Área Básica:
E1:
63X2MB/S G703/ISDN-PRA -FS PORT, 3AL79092AC** (2: 24,32). Slot position: 24, 27, 30, 32, 33, 36, 39 TRAFFIC PORTS

LEGENDA:
– (1) Multicolor LED:
• Red LED = Local unit alarm (INT)
• Green LED = In-Service unit
• Orange LED

Fast Ethernet 10/100:
ISA ES4 8FE + 1GE BOARD, 3AL81879AB** (2:36,37). Slot position: 24 to 39 ISA - ES PARTS
LEGENDA:
– (1) to (8) 10/100 Ethernet channels. It must be equipped with SFP module.
– (9) Gigabit Ethernet channel. It must be equipped with SFP module.
– (10) Factory use only
– (11) Microprocessor restart key
– (12) Bicolor LED:
• Red LED = Local unit alarm (INT)
• Green LED = In-Service unit
-------------------------------------------------...