Delta Sx2

2007-01-23

1.3 Model Information
Model name Power supply Points Input Type Points Output Type Dimension (mm) Outline

DVP32SN currently only offers TN (NPN) transistor output. Please be aware of the following PIN wiring methods for DVP32SN to prevent burn-down of the extension unit. 1. PIN19, PIN20, PIN39 and PIN40 can only connected to +24V DC. The 4 points have already been designed asshort-circuit within the extension unit; therefore only 1 of the points needs to be wired. 2. PIN17, PIN18, PIN37 and PIN38 can only connected to GND. The 4 points have already been designed as 0 N/A short-circuit within the extension unit; therefore only 1 of the points needs to be wired.

http://www.delta.com.tw/industrialautomation/

5011658300-MNE0

Digital I/O Extension Unit (Pin Headed)DVP32SM11N

32

DC Type Sink/Source

Instruction Sheet
Warning
Please read this instruction sheet carefully before use. DVP-Slim is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, electri shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required to openthe enclosure) in case danger and damage on the device may occur. DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check all the wiring again before switching on the power. DO NOT touch any terminal when the power is switched on. DVP32SN11TN

24V DC (NPN) Transistor

25.2 90

60

3.2 Connection
Step 1: Screw open the side cover of theextension unit and you will see the connection port.

0

N/A

32

Specifications
2.1 Electrical Specifications
Model Item Power supply voltage Motion specification Power consumption Insulation resistance DVP32SM11N DVP32SN11TN Step 2: Lift the fixing clip by the screwdriver.

Introduction
1.1 Model Explanation & Peripherals
Thank you for choosing Delta DVP-Slim series programmablelogic controller. DVP-Slim series pin-headed digital I/O extension unit offers 32 points. For DVP-SS/SA/SX/SC series MPU, the maximum digital I/O extension points (including the MPU) can reach 128 points. For SV series MPU, the maximum digial I/O extension points (including the MPU) can reach 256 points. In addition, maximum 8 additional special modules (AD/DA/PT/TC/XA/PU) can be extended toDVP-Slim series extension unit.

24V DC (-15% ~ 20%) (with DC input polarity reverse protection) Within 5ms of the momentary power loss, the device will keep on operating. 1W 1.5W
＞5 MΩ (all I/O point-to-ground: 500V DC) ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 1KV Damped-Oscillatory Wave: PowerLine: 1KV, Digital I/O: 1KV RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m

Noise immunity

Earth Nameplate Explanation
Delta PLC model name Power input spec. Output point module spec. Barcode & serial No. Version

24Vdc 1W 0.1A(24VDC)POINT VX.XXAX 32SN11TNT7020001
M A D E IN X X X X X

Operation/storage environment Shock/vibration immunity Weight (g)

The diameter of groundingwire shall not be less than that of L, N terminal of the power. (When many PLCs are in use at the same time, please make sure every PLC is properly grounded.) Operation: 0ºC ~ 55ºC (temperature); 50 ~ 95% (humidity); pollution degree 2 Storage: -40ºC ~ 70ºC (temperature); 5 ~ 95% (humidity) International standards: IEC1131-2, IEC 68-2-6 (TEST Fc)/IEC1131-2 & IEC 68-2-27 (TEST Ea) 70g 70g

Step3: Adjust the positioning hole of the MPU and the extension unit and meet the connection port on the MPU with the extension unit to tightly connect the two.

Model Name
DVP series Points (32 for output) Module type M: Input point extension unit N: Output point extension unit TN: NPN transistor N: No output module DC power input

Serial No.

2.2 I/O Point Specifications
Input Point...