Iso 286-2-2010

BS EN ISO 286-2:2010

BSI Standards Publication

Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes
Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts (ISO 286-2:2010)

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

raising standards worldwide™

BS EN ISO 286-2:2010

BRITISH STANDARDNational foreword
This British Standard is the UK implementation of EN ISO 286-2:2010. It supersedes BS EN 20286-2:1993 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee TDW/4, Technical Product Realization. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport toinclude all the necessary provisions of a contract. Users are responsible for its correct application. © BSI 2010 ISBN 978 0 580 70751 3 ICS 17.040.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2010 Amendments issued since publication Date Textaffected

hQÆRN«•Q

www.bzfxw.com

QM•9N•}

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
ICS 17.040.10

EN ISO 286-2
June 2010
Supersedes EN 20286-2:1993

English Version

Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts (ISO 2862:2010)
Spécificationgéométrique des produits (GPS) - Système de codification ISO pour les tolérances sur les tailles linéaires - Partie 2: Tableaux des classes de tolérance normalisées et des écarts limites des alésages et des arbres (ISO 286-2:2010) Geometrische Produktspezifikation (GPS) - ISOToleranzsystem für Längenmaße - Teil 2: Tabellen der Grundtoleranzgrade und Grenzabmaße für Bohrungen und Wellen (ISO286-2:2010)

This European Standard was approved by CEN on 15 May 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN ManagementCentre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre:Avenue Marnix 17, B-1000 Brussels

© 2010 CEN

All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.

Ref. No. EN ISO 286-2:2010: E

BS EN ISO 286-2:2010

EN ISO 286-2:2010 (E)

Foreword
This document (EN ISO 286-2:2010) has been prepared by Technical Committee ISO/TC 213 "Dimensional and geometrical product specifications and verification"in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the...