Manual canopy

Canopy™ Access Point Module (AP) User Manual

AP-UM-en Issue 5 January 2004

AP User Manual

January 2004 Software Release 4.1 NOTICES

Important Note on Modifications
Intentional or unintentional changes or modifications to the equipment must not be made unless under the express consent of the party responsible for compliance. Any such modifications could void the user’s authority tooperate the equipment and will void the manufacturer’s warranty.

U.S. Federal Communication Commision (FCC) and Industry Canada (IC) Notification
This device complies with part 15 of the U. S. FCC Rules and Regulations and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept anyinterference received, including interference that may cause undesired operation. In Canada, users should be cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250 – 5350 MHz and 5650 – 5850 MHz and these radars could cause interference and/or damage to license-exempt local area networks (LELAN). This equipment has been tested and foundto comply with the limits for a Class B digital device, pursuant to Part 15 of the U.S. FCC Rules and with RSS-210 of Industry Canada. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with these instructions, maycause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference by one or more of the following measures: Increase the separation between the affected equipment and the unit; Connect the affected equipment to a poweroutlet on a different circuit from that which the receiver is connected to; Consult the dealer and/or experienced radio/TV technician for help. FCC IDs and Industry Canada Certification Numbers are listed in the following table: Maximum Transmitter Power 340 mW 200 mW 3.2 mW 200 mW 200 mW

Module Types SM AP BH SM AP BH SM BH SM AP BH SM AP BH

Frequency Band Range ISM 2400-2483.5 MHz U-NII5250-5350 MHz U-NII 5250-5350 MHz U-NII 5725-5825 MHz ISM 5725-5850 MHz

Reflector Allowed on SM and BH Not Allowed Recommended Allowed on SM and BH Allowed on SM and BH

FCC ID ABZ89FC5808 ABZ89FC3789 ABZ89FC5807 ABZ89FC4816 ABZ89FC5804

Industry Canada Cert Number 109W-2400 109W-5200 109W-5210 109W-5700 109W-5700

The term “IC:” before the radio certification number only signifies thatIndustry Canada technical specifications were met.

European Community Notification Notification of Intended Purpose of Product Uses
This product is a two-way radio transceiver suitable for use in Broadband RLAN systems. It uses operating frequencies which are not harmonized through the EC. All licenses must be obtained before using the product in any EC country. Declaration of conformity: Motoroladeclares the GHz radio types listed below comply with the essential requirements and other relevant provisions of Directive1999/5/EC. Relevant Specification EN 301 893 or similar - radio spectrum EN301489-17 - EMC EN60950 – safety

Issue 5

Page 2 of 102

AP User Manual

January 2004 Software Release 4.1

Product Details for Products Tested for Compliance with Relevant EC DirectivesModule Type Frequency Band Range Maximum Transmitter Power Access Point Subscriber Module Subscriber Module with Reflector Backhaul 5.725 to 5.825 GHz 5.725 to 5.825 GHz 5.725 to 5.825 GHz 5.725 to 5.825 GHz 5.725 to 5.825 GHz 200 mW RMS 200 mW RMS 200 mW RMS Effective Isotropic Radiated Power (EIRP) 1 Watt EIRP 1 Watt EIRP 63 Watts EIRP Modulation Type Operating Channels Nonoverlapping Channel...