Programming Guide - Zelio Soft 2.pdf

Zelio logic tutorial
1 The Products
Congratulations! You have chosen one of the following Zelio products:

2 Environment
Zelio Logic is programmable using the Zelio Soft program or in Direct Entry Mode (Ladder language). Zelio Soft allows you to program your software in FBD language or in Ladder language. You must be connected to your PC in order to use the software program. Use an SR2CBL01cord to connect to your PC's serial port.

1

3 Introduction to Zelio Soft
3.1 STARTING THE PROGRAM When the Zelio Soft program is launched, the following window appears:

Click on Create a new program to start or choose New in the File menu if the program has already been launched. The smart relay option window now appears:

(1)

(2)

(3)

(4)

(5)

(6)

2

In thisexample, we will choose the SR2 B121 BD module: Click on the category (1) 10/12_I/O_WITHOUT_EXTENSION The selected category is highlighted in yellow and followed by the list of corresponding modules:

Click on the corresponding line to select the SR2 B121 BD module:

3

Then click on Next. The program type option screen now appears:

Ladder language is selected by default (yellow outline),click on Next to program in Ladder. Click on the FBD icon then on Next to program in FBD. Refer to 3.2 (Ladder language) or 3.3 (FBD) for an example. 3.2 EXEMPLE IN LADDER LANGUAGE 3.2.1 Program Editing: We are going to use the following example: I1—————Q1 Input I1 is connected to output Q1, which will be in active status (coil in contact mode). To reproduce this example in the wiring sheet: - Movethe mouse arrow over the Discreet Input icon in the lower left corner:

4

A chart with the different contact possibilities (I1 à IE) appears. Select contact I1 in the chart by clicking and dragging the contact to the first cell in the upper left corner of the wiring sheet. Release the mouse button: Contact I1 is now

- Now move the mouse arrow over the Discreet Output the screen: A chartwith the different contact or coil possibilities appears.

icon at the bottom of

- Select the coil [ in the first line of the chart by clicking and dragging the appropriate coil to the first line of the coil column in the wiring sheet. Release the mouse button: Coil [Q1 is now in place.

Wire the contact to the coil by clicking on the corresponding dotted lines.

5

3.2.2 Programsimulation Simulate the program chosen by clicking on the simulation icon in the upper right corner:

The chosen program is now compiled and the simulation screen appears. Next click on the RUN icon to simulate the module start-up:

A contact or a coil appears in blue if inactive (0) and in red if active (1). Click left to force input Click on the I1 contact to activate. The Q1 coil is now activated.When you click a second time on I1 to disactivate, Q1 is also disactivated.

3.2.3 Program transfer Power on the module and connect it to the computer before transferring the program: - Click on the corresponding icon to return to Edit mode:

- In the Transfer menu, select Transfer Program then click on PC>MODULE.
6

Note 1: You cannot write in the module when it is running. Click on STOPModule in the Transfer menu to stop the module. Note 2: If the module connected to the computer is not the module selected when starting the program, you may select another module by clicking on Module/programming option in the Module menu. Note 3: When you have loaded a program in FBD in the preceding module (or when you first use it), the program should update the module firmware. You will beoffered the option to update during transfer. After confirmation, the program is transferred to the module. You can then test the program that is in the module by starting it up (in the application: Click on RUN Module in the Transfer menu). As in the simulation, if the Zelio Logic I1 input is active, Q1 will be active, and if the I1 is inactive, so is Q1. 3.2.4 Monitoring Mode When the module is...