Servos

Manual 12/2004 Edition

sinumerik
SINUMERIK 840D Configuring NCU

System Overview

1 2 3 4 5 6 7 8

Connection Conditions

Design and Installation

SINUMERIK 840D Software Version 6 Configuring NCU
Manual

Description of the NCU

I/O Modules

Terminal Block

DMP Compact Modules

Maintenance and Service

Abbreviations
Valid for Control SINUMERIK SINUMERIK SINUMERIKSINUMERIK

A B

References
840D 840DE (export version) 840D powerline 840DE powerline

EC Declaration of Conformity

C

Drive SIMODRIVE 611 digital

Index

12.2004 Edition

SINUMERIK Documentation
Printing history Brief details of this edition and previous editions are listed below. The status of each edition is shown by the code in the “Remarks” column. Status code in the“Remarks” column: A . . . . . New documentation. B . . . . . Unrevised reprint with new Order No. C . . . . . Revised edition with new status. If factual changes have been made on the page since the last edition, this is indicated by a new edition coding in the header on that page.

Edition 06.94 08.94 02.95 04.95 09.95 03.96 08.97 12.97 12.98 08.99 04.00 10.00 09.01 11.02 11.03 12.04

Order No.6FC5297-0AC10-0BP0 6FC5297-0AC10-0BP1 6FC5297-2AC10-0BP0 6FC5297-2AC10-0BP1 6FC5297-3AA01-0BP0 6FC5297-3AC10-0BP0 6FC5297-4AC10-0BP0 6FC5297-4AC10-0BP1 6FC5297-5AC10-0BP0 6FC5297-5AC10-0BP1 6FC5297-5AC10-0BP2 6FC5297-6AC10-0BP0 6FC5297-6AC10-0BP1 6FC5297-6AC10-0BP2 6FC5297-6AC10-0BP3 6FC5297-7AC10-0BP0

Remarks A C C C Description of differences C C C C C C C C C C C

Trademarks SIMATICr, SIMATICHMIr, SIMATIC NETr, SIROTECr, SINUMERIKr and SIMODRIVEr are registered trademarks of Siemens AG. Other product names used in this documentation may be trademarks which, if used by third parties, could infringe the rights of their owners.
Other functions not described in this documentation might be executable in the control. However, no claim can be made regarding the availability of these functionswhen the equipment is first supplied or in the event of servicing. We have checked that the contents of this document correspond to the hardware and software described. Nevertheless, differences might exist and therefore we cannot guarantee that they are completely identical. The information given in this publication is reviewed at regular intervals and any corrections that might be necessary aremade in the subsequent printings. Suggestions for improvement are also welcome. Subject to change without prior notice.

Further information is available on the internet under: http://www.siemens.com/motioncontrol This publication was produced with Interleaf V 7



Siemens AG, 1994–2004. All rights reserved

Order no. 6FC5 297-7AC10-0BP0 Printed in Germany

Siemens AktiengesellschaftPreface
Notes for the reader
The SINUMERIK documentation is sub-divided into 3 parts:

S General Documentation S User documentation S Manufacturer/Service documentation
For more detailed information on SINUMERIK 840D publications and other publications covering all the SINUMERIK controls, please contact your local SIEMENS office.

Hotline

Should you have any questions about yourcontroller, please contact the following hotline: A&D Technical Support Tel.: +49 (180) 5050 222 Fax: +49 (180) 5050-223 http:/www.siemens.com/automation/support-request

Should you have any questions about the documentation (suggestions, corrections), please fax them to: Fax: +49 (9131) 98-2176 email: motioncontrol.docu@siemens.com Fax reply form: See the reply form at the end of the brochureInternet address

http://www.siemens.com/motioncontrol

Subject matter of this manual

Armed with the information contained in this manual, it is possible to install the SINUMERIK 840D numerical control and take measures to maintain and service it.

Who is this manual intended for?

S Project planning engineers, electricians and fitters S Service and operating personnel

 Siemens AG,...