Control De Acceso
CD CONTENTS
Up to 9 simultaneous clients:
Client # 2
Only ONE Server! (Includes 1 client)
Up to 32 simultaneous connections to Server (panel networks)
Panel Network (string) # 1 P ane l 1 Panel Network # 2
Pan el Pan
2
16
el
LAN
OVERVIEW
Int
egr
a32
Client # 3Client # 10
Se
rve
r
Pan
Panel Network # 32
USB
1
el
Pan
2
el
Pan
16
el
RS-485 Bus
Thin and Web clients are available for Internet connections
Install driver from Integra32 CD before plugging converter into USB port ! A+ B- FGND To more Panels T/RA+ BFGND Verify COM port number assigned to this device in Windows Device Manager
Int
Up to 32 doors(16 of 2-door panels) per Panel Network (string)
USB TO RS-485
egr
Se
r rve
a32
USB
RS-485 IRC o RBH-H485-USB
UR r C
Int
egr
Se
r rve
a32
RS-232
IRC 200 0
T/R+
Up to 4,000’ Max from PC to last Panel 18-22 AWG 2-Cond. Shielded, Twisted
Up to 50’ Max @ 9.6K to IRC-2000 only 18-22 AWG 3-4 Cond. Shielded Static IP Address Required 12 VDC
RS-232 -RS-485 Selector Set depending on interface used, also set same in the LIF’s configuration web page
232 485 RS232 9-30V + 9-30V 485 + 485 -
TRANS
POWER
I
ETHERNET LAN GATEWAY - LIF-2000
RS-232 to IRC Panel ONLY! Alternative to RS-485 connection, uses built in RS232/485 converter on IRC-2000 12 VDC from IRC or URC Panel RS-485 to IRC or URC Panels
Se
gr nte
r rve
a32LAN
IRC 200 0
RBH-LIF-200 Up to 4,000’ Max from LIF-200 to last Panel 18-22 AWG 2-Cond. Shielded, Twisted RJ45 100M LINK A. LIF-200 and PC are on the same subnet: LIF : XXX.XXX.ZZZ.AAA PC : XXX.XXX.ZZZ.BBB To configure LIF-200 type in it’s address into web browser. B. LIF -200 and PC are on the same net, different subnets: LIF : XXX.XXX.ZZZ.AAA PC : XXX.XXX.YYY.BBB Use IPLocator to detectLIF-200 and change it’s IP address, go to A C. LIF-200 and PC are on different nets and/or subnets: Manually set your PCs IP address to match net/subnet of the LIF-200, go to A to configure LIF-200 Static Internet IP Address for Router CAT5 Broadband Modem Static LAN IP Address Required for LIF 12 VDC IR C CAT5 (300’ Max.) 2 RBH-LIF-200
POWER LED: On - powered on 100M LED: On - 100M Ethernet isdetected LINK LED: On - network connected TRANS LED: Blinks green - being polled by software, off when not; Provides blink status code immediately after power up. Refer to LIF-200 manual for default password and reset procedures Default IP address : 192.168.168.125 Default IP port : 3002
RBH does not provide tech support on port forwarding!
Int egr a32
PC to Router to Internet to Router toLIF-200 to Controller
INTERNET
Se
rve
r
Internet
000
Router on site
Port Forwarding - Configure Router to forward designated IP port on Internet IP address (as entered in Integra32) to a port on Local Network (LIF-200). Example: In Integra32 software set 5.6.23.7 port 75. On remote router forward remote site port 75 on 5.6.23.7 to LIF-200 on port 3002 on 192.168.1.125
TIP:Use Windows built-in Telnet client to test communications with LIF-200 (you may need to enable it first in Windows Vista, 7)
This test verifies possibility of a successful connection from Integra32 Server PC to LIF-200: it checks if IP address exists and whether LIF is using right port. Example: at command prompt on Integra32 Server PC type in: telnet (c:\telnet 192.168.1.125 3002) hit“Enter”. If all is OK you will see blank screen with blinking cursor and “Trans” light on LIF will light up, if this does not happen contact IT staff for troubleshooting.
RS-232 SERIAL
PC SPEC
Server : Installs Server and Client on one PC only (Setup.exe) Communications Modules : USB Drivers and utilities (LIF-200, etc.) Documents : All manuals in PDF format License : Feature Key Client :...
Regístrate para leer el documento completo.