D16510

6DATA SHEET

MOS INTEGRATED CIRCUIT

µPD16510

VERTICAL DRIVER FOR CCD SENSOR

The µPD16510 is a vertical driver dedicated for CCD area image sensors that incorporates a level conversion circuit and a three-level output function. It contains a CCD vertical register driver (4 channels) and a VOD shutter driver (1 channel). The µPD16510, which uses the CMOS process, provides optimumtransmission delay and output ON resistance characteristics for the vertical drive of CCD sensors. It can be used for low-voltage logic (logic power-supply voltage: 2.0 to 5.5 V).

FEATURES
• CCD vertical register driver : 4 channels, VOD shutter driver: 1 channel • Small package • High breakdown voltage • Low output ON resistance • Latch-up free • Pin-compatible with µPD16506 (CCD driver) : 20-pinplastic shrink SOP (225 mil) : 33 V MAX. : 30 Ω TYP.

• Low voltage operation (logic power-supply voltage: 2.0 to 5.5 V)

APPLICATIONS
• Camcorders

ORDERING INFORMATION
Part Number Package 20-pin plastic shrink SOP (225 mil)

µPD16510GR-8JG

The information in this document is subject to change without notice. Document No. S12191EJ2V0DS00 (2nd edition) (Previous No. IC-3448) DatePublished May 1997 N Printed in Japan

The mark

shows major revised points.

1994

µPD16510
BLOCK DIAGRAM

Vsb VDD1 VSS TI1

20 16 VDD1 2 7 VDD2a Three level VSS

4

VDD2a

19 VDD2b

5

TO1

PG1 BI1

8 Two level 9 Input interface (2.0 to 5.5 V) VDD1

VDD2b 3 VSS VDD2a Three level 17 TO2 BO1

TI2 PG2 BI2

14 13 12

VSS VDD2b Two level 18 BO2 VSS Vsb Two level 1 VSSSUBO

SUBI NC

10 11

VCC

6

GND

15

2

µPD16510
PIN CONFIGURATION
20-pin plastic shrink SOP (225 mil)

SUBO VSS BO1 VDD2a TO1 VCC TI1 PG1 BI1 SUBI

1 2 3 4 5 6 7 8 9 10

20 19 18 17 16 15 14 13 12 11

Vsb VDD2b BO2 TO2 VDD1 GND TI2 PG2 BI2 NC

Remark

The µPD16510 is pin-compatible with the µPD16506 (CCD driver). However, the VOD shutter drive pulse input polarityswitching pin (SSP) of the µPD16506 corresponds to the GND pin in the µPD16510 (pin 15).

PIN FUNCTIONS
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol SUBO VSS BO1 VDD2a TO1 VCC TI1 PG1 BI1 SUBI NC BI2 PG2 TI2 GND VDD1 TO2 BO2 VDD2b Vsb I/O O – O – O – I I I I – I I I – – O O – – Ground VH power supply Three-level pulse output Two-level pulse output VMb (Two-level driver) powersupply VHH (for SUB drive) power supply Two-level driver input (See Functions table on p. 4) VOD shutter drive pulse input Non connect Two-level driver input (See Functions table on p. 4) Three-level driver input (See Functions table on p. 4) Pin Function VOD shutter drive pulse output VL power supply Two-level pulse output VMa (Three-level driver) power supply Three-level pulse output Logic powersupply Three-level driver input (See Functions table on p. 4)

3

µPD16510
FUNCTIONS
VL = VSS, VMa = VDD2a, VMb = VDD2b, VH = VDD1, VHH = Vsb Pin TO1
Input TI1 L L H H PG1 L H L H VH VMa VL Output (TO1) TI2 L L H H

Pin TO2
Input PG2 L H L H VH VMa VL Output (TO2)

Pin BO1
Input BI1 L H VMb VL Output (BO1)

Pin BO2
Input BI2 L H VMb VL Output (BO2)

Pin SUBO
Input SUBI L H VHHVL Output (SUBO)

Usage Caution
Because the µPD16510 contains a PN junction (diode) between VDD2 → VDD1, if the voltage is VDD2 > VDD1, an abnormal current will result. Therefore, apply power in the sequence VDD1 → VDD2, or apply power simultaneously to VDD1 and VDD2.

4

µPD16510
ELECTRICAL SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS (Unless otherwise specified, TA = 25 ˚C, GND = 0 V)Parameter Power supply voltage Power supply voltage Power supply voltage Power supply voltage Input voltage Operating ambient temperature Storage temperature Power dissipation Symbol VCC VDD1 VDD2 Vsb VI TA Tstg Pd T A = 85 °C Conditions Rating VSS–0.3 to VSS +20.0 VSS–0.3 to VSS +33.0 VSS–0.3 to VSS +33.0 VSS–0.3 to VSS +33.0 VSS–0.3 to V CC+0.3 –25 to +85 –40 to +125 260 Unit V V V V V °C °C mW...