Ensayo

Important note — emergency calls
The e3300 is not designed for making emergency
calls when the mains power fails. So you should
make alternative arrangements for access to
Emergency Services.
(This means that you should also have a basic
phone that does not need mains power, connected
to your line so that you can make calls during a
power failure.)

If you need help …
The Binatone HelpLine is available from 9.00 am to
5.00 pm, Monday to Friday, on
01325 304 473

Unpacking your e3300
In the box are:
I

the cordless handset (one for a Single system,
two/three for a Twin/Triple system)

I

the base unit

I

rechargeable batteries and a battery
compartment cover for each handset

I

a telephone line cable for the base unit

I

a mains power lead andadapter for the base
unit

I

if you have a Twin or Triple system, one or two
charger pods, each with a separate mains
power lead and adapter.

Keep the packaging materials in a safe place in
case you later need to transport the unit.
Keep your sales (till) receipt, which is your
guarantee.

Symbols on the display

Where to find it
UP L and DOWN M buttons
Press during a call toadjust the volume
in the earpiece.
Press to move through the list of stored
numbers or Caller Display records.

HANG UP / C (Cancel) button
Press to hang up at the end of a call.
Press for 1 second to lock the keypad;
or for 3 seconds to turn the handset
on and off.
While dialling or programming,
press briefly to delete digits from
the display; or press and hold to
clear the display.PHONE
/OK button
Press to begin or answer a
telephone call.
Press while programming to
confirm your selection.

The time is shown if you’ve
set the handset’s clock
The handset’s
number (1 if you
have a single system,
1, 2 or 3 if you have
a Twin or Triple
system)

The base unit’s number (1,
unless you have registered
your handset to more than
one base unit)
The duration of eachcall is shown on the display from 20 seconds
after you press the PHONE button for a line, until 5 seconds after
you end the call.

R (Recall) button
You may need this
during a call if your
e3300 is connected to a
PBX, or if you use BT’s
Select Services.

What the symbols mean

MEMORY
button
Press to store numbers in
memory and to make
calls to stored numbers.

LNR/ CDS/ PAUSEbutton
Press ONCE to make a repeat call
to one of the last five numbers
you dialled.
Press TWICE to see a list of Caller
Display records.
Press to generate pauses when
using the phone on a PBX.
INT (✱) button
Press to make an
intercom call.

IN USE light
This comes on when you
have a connection to the
telephone line.
HANDSET LOCATOR button
Press to make all registered
handsets ring,(useful if
you've forgotten where you
put a handset).
SCROLL (✱ #) buttons
When a long number
(more than 16 digits) is
shown on the display,
press these to scroll along
the digits.

Before you can use the handset to make calls
you will need to fit and fully charge the
batteries, as described on pages 4 and 5.
Please read the notes on pages 2 and 3
before you install the base unit.Signal
level

This shows the strength of the signal between the handset
and base unit. It flashes while the handset is trying to
establish a radio link to the base unit. If this symbol flashes
while you’re on a call, move closer to the base unit.

New call

This appears when you missed incoming calls (even if you
do not use Caller Display).

Intercom
call

This flashes while yourhandset is ringing for an intercom call,
and comes on steadily when the call’s connected.

Memory/
store

This comes on when you’re storing numbers in memory, and
when you’re making calls to stored numbers.

Indirect
network

This appears when the handset is dialling a non-local
number via an alternative provider’s network.

Redialling

This appears when you’re using Last...