Facility Planning Ups Apc

Facility Planning
Specifications for Installations
AC Input
Input Voltage and Connections Specifications
UPS VA
1000 2000 2200 3000
Nominal
Input Voltage
3.5 A 6.8 A
10,000
15,000
10.5 A
20,000
40-70 Hz
(auto-sensing)
230 V or 400 V
16.5 A
20A
1PH: 40 A;
3PH:
15 A/phase
when online,
40 A on L1
(in bypass
only)
1PH: 50 A;
3PH:
18 A/phase
when online,
50 A on L1
(inbypass
only)
1:1: 83 A; 1:1: 105 A;
3:1: 83 A 3:1: 105 A
(in bypass (in bypass
only); 3:3:
only);
28 A each 3:3: 35 A
phase
each phase
Automatic and Manual (Built-In)
British BS1363A; Hard Wire
IEC-320 C20; 3-wire
Schuko CEE 7/EU1-16P (1PH+N+G)
Not applicable 6 mm2
Wire Size
(Typical)**
External
Input Circuit
Breaker
(Typical)***
8000
230 V
Bypass
Input
Connections*
600045-65 Hz
(auto-sensing)
Input
Frequency
(Hz)
Current Full
Load
(Nominal)
5000
10 A
16 A
32 A
Hard Wire 3-wire (1PH+N+G); Hard Wire 5-wire
(3PH+ N+G)
10 mm2
16 mm2
1PH:
1PH:
50 A/ 2-pole; 63 A/ 2-pole;
3PH:
3PH:
50 A/4-pole
63 A/4-pole
1:1 and 1:1 and
3:1: 3:1:
35 mm2, 50 mm2,
3:3: 3:3:
6 mm2 10 mm2
1:1 and 1:1 and
3:1: 3:1: 125 A
100 A each
each phase;
phase; 3:3: 50A
3:3: 35 A each
or 40 A phase
each
phase
* Wire connection “G” represents protective earth ground.
** Recommended wire sizes are typical. Actual wire size must comply with local and national electrical codes.
Note: For units configured for 3-phase input and single-phase output operation, the entire load connected to the
UPS will transfer to L1 and Neutral of the 3-phase input when theUPS is operating in bypass mode.
*** The notation 1:1 refers to a UPS configured for single-phase AC input and output, the notation 3:1 refers to
a UPS configured for 3-phase input and single-phase output, and the notation 3:3 refers to a UPS configured for 3-
phase input and 3-phase output.
20
Smart-UPS On-Line, 230 V, 1 kVA to 20 kVA Technical Specifications
990-4769
AC Input (continued)Model
SKU
APC Smart-UPS RT 1000 VA RM 230 V SURT1000RMXLI
APC Smart-UPS RT 1000 VA 230 V SURT1000XLI
APC Smart-UPS RT 2000 VA RM 230 V SURT2000RMXLI
APC Smart-UPS RT 2000 VA 230 V SURT2000XLI
APC Smart-UPS RT 3000 VA, 230 V with Pre-installed SURT3000XLI-ET
Input/Output Hardwire Kit
APC Smart-UPS RT 3000 VA RM 230 V SURTD3000RMXLI
APC Smart-UPS RT 3000 VA SURTD3000XLI
APC Smart-UPS RT5000 VA RM 230 V SURTD5000RMXLI
APC Smart-UPS RT 5000 VA 230 V SURTD5000XLI
APC Smart-UPS RT 5000 VA 230 V with Pre-installed SURTD5000XLI-ET
Input/Output Hardwire Kit
APC Smart-UPS RT 6000 VA RM 230 V SURT6000RMXLI
APC Smart-UPS RT 6000 VA 230 V SURT6000XLI
APC Smart-UPS RT 6000 VA 230 V with Pre-installed SURT6000XLI-ET
Input/Output Hardwire Kit
APC Smart-UPS RT 8000 VA RM 230 VSURT8000RMXLI
APC Smart-UPS RT 8000 VA 230 V SURT8000XLI
APC Smart-UPS RT 10,000 VA RM 230 V SURT10000RMXLI
APC Smart-UPS RT 10,000 VA 230 V SURT10000XLI
APC Smart-UPS RT 15 kVA RM 230 V SURT15KRMXLI
APC Smart-UPS RT 20 kVA RM 230 V SURT20KRMXLI
APC Smart-UPS RT 1000 VA 230 V – Marine SURT1000XLIM
APC Smart-UPS RT 2200 VA 230 V – Marine SURTD2200XLIM
APC Smart-UPS RT 3000 VA 230 V – MarineInput Voltage Range
1
for Main Operation
SURTD3000XLIM
160 V to 280 V
160 V to 280 V or
3-phase: 277 V to 485 V
180 V to 280 V
180 V to 270V
SURT6000XLIM
APC Smart-UPS RT 6000 VA 230 V – Marine
1
These voltage ranges are for operation at full load. At half load, the UPS will run at voltage levels down to 100V,
but will neither start up nor charge the battery at this level. Therefore, donot attempt to run the unit at input
voltages below these ranges. For example, do not attempt to use a 110 V input supply for 230 V output even at a
reduced load.
21
Smart-UPS On-Line, 230 V, 1 kVA to 20 kVA Technical Specifications
990-4769
AC Output
Output Specifications
UPS VA
1000
2000
2200
3000
5000
10,000
15,000
20,000
Configurable for
220, 230, 240,
380, 400, 415 V...