Implementacion De Procesos
Páginas: 3 (690 palabras)
Publicado: 19 de junio de 2012
A
Introduction
CUTTING DATA
CoroCut® 1-, 2- and 3-edge
Cutting speed recommendations
The recommendations are valid for use with cutting fluid.
Specific cutting force kc 0.4 CMC ISO No. P01.1 01.2 01.3 02.1 02.2 02.2 Steel 03.11 03.21 06.1 06.2 06.3 06.33 Material Unalloyed C = 0.1–0.25% C = 0.25–0.55% C = 0.55–0.80% Low-alloy ≤5% Non-hardened Hardened and tempered Hardened andtempered High-alloy >5% Annealed Hardened tool steel Castings Unalloyed Low-alloy (alloying elements ≤5%) High-alloy (alloying elements >5%) Manganese steel, 12–14% Mn N/mm2 2000 2100 2200 2150 2550 28502500 3900 2000 2100 2650 3600 Specific cutting force kc 0.4 CMC ISO No. M 05.11 05.12 05.13 Material Ferritic/martensitic Bars/forged Non-hardened PH-hardened Hardened Austenitic Bars/forged AusteniticPH-hardened Super austenitic Austenitic-ferritic (Duplex) Bars/forged Weldable < 0.05%C Ferritic/martensitic Cast Non-hardened Hardened Austenitic Cast Austenitic PH-hardened Austenitic-ferritic(Duplex) Cast Non-weldable ≥ 0.05%C Weldable < 0.05%C N/mm2 Hardness Brinell >> GC2145 0.05-0.5
C
Internal machining
D
165-75 130-60 140-65 160-70 120-55 130-55 145-65 110-45 120-50 130-100 90-70100-75 130-50 110-40 110-45
185-90 130-60 140-65
175-80 120-55 130-60
165-70 105-50 115-55
125-95 75-55 85-65
140-55 95-45 105-50
155-75 130-60
145-70 120-55
135-60 110-50125-95 95-70
125-50 100-45
E
150-70 125-55
140-65 120-50
130-60 110-45
110-85 70-55
120-45 100-40 Drilling
160-80 105-55
150-70 95-50
135-60 90-45
105-80 65-50
125-5080-38
135-65 110-55
125-60 105-50
115-55 95-45
110-85 85-60
105-45 80-39
F
G
H
CUTTING DATA CoroCut ® 1-, 2- and 3-edge
F9
General Information
Grades
Cutting dataMilling
A
Introduction
CUTTING DATA
CoroCut® 1-, 2- and 3-edge
Cutting speed recommendations
The recommendations are valid for use with cutting fluid.
Specific cutting force kc...
Introduction
CUTTING DATA
CoroCut® 1-, 2- and 3-edge
Cutting speed recommendations
The recommendations are valid for use with cutting fluid.
Specific cutting force kc 0.4 CMC ISO No. P01.1 01.2 01.3 02.1 02.2 02.2 Steel 03.11 03.21 06.1 06.2 06.3 06.33 Material Unalloyed C = 0.1–0.25% C = 0.25–0.55% C = 0.55–0.80% Low-alloy ≤5% Non-hardened Hardened and tempered Hardened andtempered High-alloy >5% Annealed Hardened tool steel Castings Unalloyed Low-alloy (alloying elements ≤5%) High-alloy (alloying elements >5%) Manganese steel, 12–14% Mn N/mm2 2000 2100 2200 2150 2550 28502500 3900 2000 2100 2650 3600 Specific cutting force kc 0.4 CMC ISO No. M 05.11 05.12 05.13 Material Ferritic/martensitic Bars/forged Non-hardened PH-hardened Hardened Austenitic Bars/forged AusteniticPH-hardened Super austenitic Austenitic-ferritic (Duplex) Bars/forged Weldable < 0.05%C Ferritic/martensitic Cast Non-hardened Hardened Austenitic Cast Austenitic PH-hardened Austenitic-ferritic(Duplex) Cast Non-weldable ≥ 0.05%C Weldable < 0.05%C N/mm2 Hardness Brinell >> GC2145 0.05-0.5
C
Internal machining
D
165-75 130-60 140-65 160-70 120-55 130-55 145-65 110-45 120-50 130-100 90-70100-75 130-50 110-40 110-45
185-90 130-60 140-65
175-80 120-55 130-60
165-70 105-50 115-55
125-95 75-55 85-65
140-55 95-45 105-50
155-75 130-60
145-70 120-55
135-60 110-50125-95 95-70
125-50 100-45
E
150-70 125-55
140-65 120-50
130-60 110-45
110-85 70-55
120-45 100-40 Drilling
160-80 105-55
150-70 95-50
135-60 90-45
105-80 65-50
125-5080-38
135-65 110-55
125-60 105-50
115-55 95-45
110-85 85-60
105-45 80-39
F
G
H
CUTTING DATA CoroCut ® 1-, 2- and 3-edge
F9
General Information
Grades
Cutting dataMilling
A
Introduction
CUTTING DATA
CoroCut® 1-, 2- and 3-edge
Cutting speed recommendations
The recommendations are valid for use with cutting fluid.
Specific cutting force kc...
Leer documento completo
Regístrate para leer el documento completo.