Lavadoras

8-4. ERROR DISPLAY.
I WD-1223(5)F(H)(B)/WD-1243(5)F(H)(B)/WD-102(4)1(5)WF(H) / WD-1041(3)F(H)B If you press the Start/Pause button when an error in displayed, any error except will disappear and the machine will change into pause status. In case of if the error is not resolved within 20 sec. In the case of other errors, if the error is not resolved within 4 min. power will be turned offautomatically and the error code will blink. But in case of FE , power will not be turned off. ERROR
1 WATER INLET ERROR

SYMPTOM

CAUSE
Water has not reached to the pre-set level within 4 min. since

no inlet

inlet valve operated, or water has not reached to the normal level within 25 min.

2

IMBALANCE ERROR

imbalance

The appliance is tilted. Laundry is gathered to one side.Non-distributable things are put into the drum.

3

DRAIN ERROR

no drain

Water has not drained enough within 5 min.

4

OVERFLOW ERROR

Water is automatically being pumped out because too much water is in the tub.

5

SENSOR PRESSURE The sensor pressure switch is out of order. S/W ERROR

6

DOOR OPEN ERROR HEATING ERROR

The Start/Pause button is pressed with the door open. Thedoor switch is out of order. The thermistor is out of order.

7

8

SENSOR ERROR

The connector (5-pin, male, white) in the wire harness is not connected to the connector (5-pin, female) of hall sensor in the MOTOR. ’ Reconnect or repair the contact in the connector.

22

ERROR 8
SENSOR ERROR

SYMPTOM

CAUSE
• The electric contact between the connectors (5-pin, male in the wireharness and 5-pin female in the hall sensor) is bad or unstable. Reconnect or repair the contact in the connector. • The connector (6-pin, male, natural) in the wire harness is not connected to the connector (6-pin, female, natural) of PWB assembly (Main) or the electric contact of connectors is bad/unstable. Reconnect or repair the contact in the connector. • The electric contact between theconnectors 6-pin, male in the wire harness and 6-pin female in the controller (Main) is bad or unstable. Reconnect or repair the contact in the connector. • The wire harness between hall sensor in the MOTOR and PWB assembly (Main) is cut (open circuited). Repair/replace the damaged WIRE HARNESS. • The hall sensor is out of order/defective. Replace the motor. • The controller (Main) is out oforder/defective. Replace the PWB assembly (Main). • PWB assembly (Main) is out of order. Replace the PWB assembly (Main). • Winding in the MOTOR is short-circuited. Replace the MOTOR. • The connector (3-pin, male, white) in the wire harness is not connected to the connector (3-pin, female, white) of MOTOR. Reconnect or repair the connector. • The electric contact between the connectors 3-pin, male, whitein the wire harness and 6 pin, female, white in the PWB assembly (Main) is bad or unstable. Reconnect or repair the contact in the connector. • The wire harness between the MOTOR and PWB assembly (Main) is cut (open circuited). Repair the damaged (open-circuited) WIRE HARNESS. • The hall sensor is out of order/defective. Replace the PWB assembly (Main).

9

CURRENT ERROR

10

LOCK ERROR23

I WD-8030(W)(F)(H)/WD-8040W(F)(H)/WD-1042F(H)/WD-803(4)0F(H)B/WD-102(4)2F(H)B If you press the Start/Pause button when an error in displayed, any error except SENSOR PRESSURE S/W ERROR will disappear and the machine will change into pause status. In case of SENSOR PRESSURE S/W ERROR, THERMISTOR ERROR if the error is not resolved within 20 sec. In the case of other errors, if the error isnot resolved within 4 min. power will be turned off automatically and the error code will blink. But in case of OVER FLOW ERROR , power will not be turned off. ERROR
1 WATER INLET ERROR IMBALANCE ERROR

SYMPTOM
Pre Main Rinse Hold Super Normal
800 (1000) 600 (800) no Spin (600) 1000 800 600 400 no spin
for WD-8030F(H)B WD-8040F(H)B WD-1022F(H)B WD-1042F(H)B

CAUSE
Water has not reached to...