Manual Reparación Motor Clio

N.T. 3286A CB0M
Basic manual: M.R. 337

Special features of vehicles fitted with the F4R 730 engine

For parts not dealt with in this technical note, refer to Workshop Repair Manual M.R. 337 M.R. 337 Cancels and replaces Technical Note 3243A 77 11 206 241
"The repair methods given by the manufacturer in this document are based on the technical specifications current when it was prepared.The methods may be modified as a result of changes by the manufacturer in the production of the various component units and accessories from which his vehicles are constructed".

JULY 1999
All copyrights reserved by Renault.

Edition Anglaise

Copying or translating, in part or in full, of this document or use of the service part reference numbering system is forbidden without the priorwritten authority of Renault.

C RENAULT 1999

Contents
Pages Pages

07 VALUES AND SETTINGS
Capacities - Grades Accessories belt tensioning Timing belt tensioning procedure Cylinder head tightening Underbody height Tyres - wheels Brakes Brake compensator Underbody height Values for checking front axle geometry Values for checking rear axle geometry 07-1 07-3 07-4 07-30 07-31 07-32 07-33 07-3407-35 07-36 07-37

13 FUEL SUPPLY
Anti-percolation system 13-1

14 ANTIPOLLUTION
Fuel vapours rebreathing 14-1

16 STARTING - CHARGING
Alternator Starter 16-1 16-3

10 ENGINE AND PERIPHERALS
ASSEMBLY Identification Oil pressure Engine and transmission assembly Sump Accessories support 10-1 10-2 10-3 10-9 10-12

17 IGNITION - INJECTION
Specifications Engine immobiliser functionInjection/AC strategy Idle speed correction Adaptive idle speed correction Mixture regulation Adaptive mixture correction Centralised coolant temperature management Camshaft phase shifter Computer Wiring diagram Fault finding - conformity check 17-1 17-2 17-3 17-4 17-5 17-6 17-8 17-9 17-10 17-11 17-12 17-15

11 TOP AND FRONT OF ENGINE
Timing belt Cylinder head gasket 11-1 11-8

12 FUEL MIXTURESpecifications Inlet manifold Injectors support Exhaust manifold 12-1 12-4 12-6 12-9

Contents
Pages Pages

19 COOLING
Diagram Filling- Bleeding Radiator Coolant pump ENGINE MOUNTING SYSTEM Suspended engine mounting 19-1 19-2 19-3 19-4

36 STEERING ASSEMBLY
Power steering unit Mechanical power steering pump 36-1 36-5

19-6

38 ELECTRONICALLY CONTROLLED
HYDRAULIC SYSTEM

20 CLUTCHCover - Disc Flywheel 20-1 20-4

BOSCH anti-lock brake system

38-1

62 AIR CONDITIONING
General Compressor Condenser Pressure relief valve Dehydration canister 62-1 62-2 62-3 62-4 62-5

21 MANUAL GEARBOX
Identification Gears Capacity - Lubricants Consumables Parts which must always be changed Special features 21-1 21-2 21-3 21-4 21-4 21-5

33 REAR BEARING ELEMENTS
Brake linings (Disc)Brake caliper Brake hub - disc Hub - disc bearing Stub axle and brake caliper support 33-1 33-3 33-6 33-7 33-8

VALUES AND SETTINGS Capacities - Grades
Capacity in litres (approx.) * When draining

07

Units Petrol engine (oil)

Grade

European Union countries and Turkey PETROL - 15 °C - 30 °C - 20 °C - 10 °C 0 °C + 10 °C + 20 °C + 30 °C 15W40-15W50 10W30-10W40-10W50

ACEA A2/A3ACEA A1*/A2/A3

ACEA A1*/A2/A3

0W30-5W30 0W40-5W40-5W50

ACEA A1*/A2/A3

ACEA A1-98 standard * Oil for fuel economy F4R 4.75 5.1 (1)

Other countries If the lubricants specified for European Union countries are not available, the following specifications must be taken into account: PETROL - 15 °C - 30 °C - 20 °C - 10 °C 0 °C + 10 °C + 20 °C + 30 °C

API SH/SJ

15W40-15W50

APISH/SJ

10W40-10W50 10W30

API SH/SJ

API SH/SJ

5W30 5W40-5W50

API SH/SJ

Oil for fuel economy: API SJ-IL SAC GF2 standard * Adjust using a dipstick (1) Following replacement of the oil filter

07-1

VALUES AND SETTINGS Capacities - Grades
Capacity in litres 3,1

07
Special features

Units JC5 gearbox F4R cooling circuit

Grade

All countries: TRANSELF TRX 75 W 80 W (API...