Puesta En Marcha Up´S

SEL-2BFR, -2/BFR

BREAKER FAILURE RELAY AND MONITOR

INSTRUCTION MANUAL

20050421

SCHWEITZER ENGINEERING LABORATORIES 2350 NE HOPKINS COURT PULLMAN, WA USA 99163-5603 TEL: (509) 332-1890 FAX: (509) 332-7990

The software (firmware), schematic drawings, relay commands, and relay messages are copyright protected by the United States Copyright Law and International Treatyprovisions. All rights are reserved. You may not copy, alter, disassemble, or reverse-engineer the software. You may not provide the software to any third party. All brand or product names appearing in this document are the trademark or registered trademark of their respective holders.
ACSELERATOR,

Connectorized, CONSELTANT, Job Done, Schweitzer Engineering Laboratories, trademarks ofSchweitzer Engineering Laboratories, Inc. The English language manual is the only approved SEL manual. Copyright © SEL 1990—2005 (All rights reserved) This product is covered by U.S. Patent Numbers: 5,157,575 and 5,479,315.

, SEL, SELOGIC, and SEL-PROFILE, are registered

This product is covered by the standard SEL 10-year warranty. For warranty details, visit www.selinc.com or contact yourcustomer service representative.

PM2BFR-01

MANUAL CHANGE INFORMATION
The date code at the bottom of each page of this manual reflects the creation or revision date. Date codes are changed only on pages that have been revised and any following pages affected by the revisions (i.e., pagination). If significant revisions are made to a section, the date code on all pages of the sectionwill be changed to reflect the revision date. Each time revisions are made, both the main table of contents and the affected individual section table of contents are regenerated and the date code is changed to reflect the revision date. Changes in this manual to date are summarized below (most recent revisions listed at top). Revision Date 20050421 20030207 20010515 990714 Summary ofRevisions Updated Appendix A: Firmware Versions in this Manual. Updated Appendix A: Firmware Versions in this Manual. Added information on the effect of 50FT pickup on IRIG-B operation in Section 2: Specifications and Section 5: Applications. Changed footers on entire manual to reflect SEL-2BFR, -2/BFR. Added Model Variation Information to Section 1: Introduction. Incorporated SEL-2BFR-2 TimeDelayed Retrip Logic into Section 2: Specifications. Modified AND and OR gate numbering in Section 2: Specifications. Reformatted Settings Sheets at end of Section 5: Event Reporting. Added Appendix C: SEL-BFR to explain SEL-BFR Relay differences. 990512 Clarified Figure 2.12 in Section 2: Specifications. Updated Appendix A: Firmware Versions in this Manual. 981019 Incorporated the followingaddenda into Section 1: Introduction: “ACB Phase Rotation Option” and “50 Hz Options.” Incorporated the following addenda into Section 2: Specifications: “New SEL-200 Series Optical Isolator Logic Input Rating” and “SEL-2BFR/BFR Instruction Manual Addendum for 1 Amp Version and 50/60 Hz Relays.” Incorporated the following addendum into Section 6: Installation: “Jumper InstallationInstructions.” Updated Figures 6.3, 6.4, and 6.5. 970423 2BFR Specifications Addendum - Addition

Date Code 20050421

Manual Change Information SEL-2BFR, -2/BFR Instruction Manual

i

SEL-2BFR, -2/BFR INSTRUCTION MANUAL TABLE OF CONTENTS

SECTION 1: SECTION 2: SECTION 3: SECTION 4: SECTION 5: SECTION 6: SECTION 7: SECTION 8:

INTRODUCTION SPECIFICATIONS COMMUNICATIONS EVENT REPORTINGAPPLICATIONS INSTALLATION MAINTENANCE AND TESTING APPENDICES

Appendix A: Firmware Versions in This Manual Appendix B: Internal Diagrams Appendix C: SEL-BFR Specifications

Date Code 20050421

Table of Contents SEL-2BFR, -2/BFR Instruction Manual

i

TABLE OF CONTENTS
SECTION 1: INTRODUCTION ............................................................1-1

Getting Started...