Call termination cause code

A P P E N D I X

A

Call Termination Cause Codes
Revised: May 14, 2009, OL-15338-06

Introduction
This appendix lists call termination cause values and definitions.

BTS 10200 Call Termination Cause Values and Definitions
Table A-1 lists the BTS 10200 call termination cause values and definitions.
Note

A “*” next to the value in Table A-1 indicates the cause code is not a standardBAF cause code; it is unique to the Cisco BTS 10200 Softswitch. All values of 400 or higher are used internally only and do not appear in the billing records transmitted from the EMS.
Table A-1 Call Termination Cause Values and Definitions

Value 1 2 3 4 6 7 8 9 10 11 12

Cause Definition Attempted termination to an unallocated or unassigned directory number. No route available to thespecified transit network. No route available to the specified destination. Vacant code. Channel unacceptable. Call awarded and being delivered in an established channel. Prefix 0 was dialed in error. Prefix 1 was dialed in error. Prefix 1 was not dialed when required. Excessive digits received, call is progressing. Call is proceeding.

In Release 6.0.x Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes YesCisco BTS 10200 Softswitch Billing Interface Guide, Release 6.0.x OL-15338-06

A-1

Appendix A BTS 10200 Call Termination Cause Values and Definitions

Call Termination Cause Codes

Table A-1

Call Termination Cause Values and Definitions (continued)

Value 13 14 16 17 18 19 21 22 23 24 25* 26*

Cause Definition The requested service was denied. Indicates an exchange detected that thecalled number was ported out. Normal call clearing. Termination called is busy. No user responding. User altering, no answer. Call was rejected. The terminating number was changed. Terminating party rejects all calls with Calling Line Identification Restriction. The destination business group is not defined. Exchange routing error occurred.

In Release 6.0.x Yes Yes Yes Yes Yes Yes Yes Yes YesYes Yes

For ANSI calls, the destination is misrouted because the number is ported out of Yes the switch. For ISDN calls, the destination is able to accept calls but no user is assigned to the endpoint.

27 28 29 30 31 34 35 36 37 38* 39 41 42 43 44 45 46 47 49 50

The specified destination was out of order. Invalid number format or incomplete address. Facility rejected. Response to STATUSENQ message. Normal, unspecified. Circuit or channel congestion. Requested VPCI/VCI was not available. VPCI/VCI assignment failure. The user cell rate was unavailable. Network out of order. The destination Permanent Virtual Circuit (PVC) is out of order. Temporary failure. Switching Equipment Congestion. Access information discarded. Requested channel not available. No VPCI/VCI available.Precedence call blocked. Network resource unavailable or unspecified. Quality of service unavailable. Requested facility not subscribed to.

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Cisco BTS 10200 Softswitch Billing Interface Guide, Release 6.0.x

A-2

OL-15338-06

Appendix A

Call Termination Cause Codes BTS 10200 Call Termination Cause Values andDefinitions

Table A-1

Call Termination Cause Values and Definitions (continued)

Value 51 53 57 58 63 65 66* 69 70 73 78 79 81 82 84* 85* 86* 88 89 90* 91 92 96 97 98* 99 100 101 102 104 111 112 120 121 122

Cause Definition Bearer capability incompatible with service request. Service operation violated. Bearer capability not authorized. Bearer capability not presently available. Service oroption unspecified. Bearer capability not implemented. Channel type not implemented. Requested facility not implemented. Restoration digital bearer capacity only available. Unsupported combination of traffic parameters. AAL parameter cannot be supported. Service or option not implemented. Invalid call reference value. Identified channel does not exist. Call id already in use. No call suspended....