Licenciado

PRINT SERVER WITH USB PORT

DP-301U
Quick Installation Guide+ Руководство по быстрой установке+ Guía de Instalación Rápida+ Guia de Instalação Rápida+ 快速安裝指南+ Petunjuk Pemasangan Cepat+

This product can be setup using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 7.0

D-Link Fast Ethernet Print Server

DP-301U

Before You Begin

You will need anEthernet-enabled device, such as a laptop or desktop computer and a USB or parallel-port printer that will connect to the DP-301U.

Important: TURN OFF the power to the printer before installing the DP-301U.

Check Your Package Contents
DP-301U USB Print Server

CD-ROM (Software, Manual and Warranty)

5V DC 2.5A Power Adapter

Using a power supply with a different voltage rating will damage thisproduct and void its warranty.

If any of the above items are missing, please contact your reseller.

©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and specifications subject to change without notice. DP-301U 02142003

Connecting The DP-301U To Your Network
First, insert one end of astraight-through CAT5 Ethernet RJ-45 cable into the “Network Port” (shown below.) Connect the other end of the cable to the LAN port of the gateway or switch. Note: Do not connect the power cord to the DP-301U until you are advised to do so

Warning! Only a USB printer may be connected to the USB port of the DP-301U. Do not connect any other USB device to the USB port; to do so may damage the unit, voidingthe warranty for this product.

Next, make sure that the Printer is turned OFF. Using the USB cable, connect one end of the cable to the USB port of the DP-301U (shown below) and the other end to the USB port of the printer. Turn ON the printer.

Receptor for AC Power Adapter

USB Port

Network Port Then, plug one end of the power adapter into the DP-301U and the other end into yourelectric outlet. The DP-301U will turn on and begin a self-test. For Mac OS printing, please refer to users manual located on CD-ROM
3

Setting up your DP-301U for network printing in Windows XP
For additional Windows operating system setup or information on the web-management interface, refer to the manual located on the CD-ROM. The factory default IP address of the DP-301U is 192.168.0.10. Inorder to print to the printer(s) through the DP-301U, the DP-301U must have the same IP network settings as your network. IP address can be assigned manually or automatically by DHCP, BOOTP or RARP. To access the print server’s web configuration, manually assign an IP address on one of the PC’s on your network to the same subnet as the print server. Go to Start > right click on My Network Places >select Properties > Double-click on the Network Connection associated with your Network Adapter.

Click Internet Protocol (TCP/IP) Click Properties

Input a static IP address in the same range as the print server.

Select Use the following IP address IP address: 192.168.0.52 Subnet mask: 255.255.255.0

Click OK
4

Setting up your DP-301U for network printing in Windows XP (continued)Click OK to apply IP address settings.

Click OK

Using your web browser enter the IP address of the DP-301U. By default the IP address is set to 192.168.0.10

The IP address of the DP-301U can be modified on the Network tab of the Web configuration menu.

The following instructions use the print server’s default IP address as an example. Make the appropriate changes if you have modifiedthe DP-301Us IP address.



Setting up your DP-301U for network printing in Windows XP (continued)
Click on the Configure tab to view the current Port Settings.

Write down on a piece of paper the Port name that you wish to use.

For Windows XP: Go to Start>Printers and Faxes>Add a Printer or Go to Start>Control Panel> Printers and Faxes

Double-click on the “Add Printer” icon...