Qwerty

Table 5-37 POST Error Messages
Screen Message 101—Option ROM Error Probable Cause System ROM checksum. Recommended Action Verify the correct ROM. 1 2 Flash the ROM if needed. If an expansion card was recently added, remove it and see if the problem remains. 3 4 Clear CMOS. If the message disappears, there might be a problem with the expansion card. 5 102—System Board Failure DMA, timers, etc. 12 3 103—System Board Failure DMA, timers, etc. 1 2 3 110—Out of Memory for Option ROMs Option ROM for a device was unable to run due to memory constraints. Replace the system board. Clear CMOS. Remove expansion boards. Replace the system board. Clear CMOS. Remove expansion boards. Replace the system board.

Run Computer Setup and enable the ACPO/USB Buffers at Top of Memory under theAdvanced>PowerOn option. 1 2 3 Restart the workstation. Disable SafePost. If the expansion card does not respond, replace the card.

150—SafePost Active

A PCI expansion card is not responding.

162—System Options Not Set

Configuration incorrect. RTC battery might need to be replaced.

1 2

Run Computer Setup (F10 Setup). Set the date and time under Control Panel or in F10 Setup depending on theoperating system.

3 163—Time and Date Not Set Invalid time or date in configuration memory. RTC (real-time clock) battery might need to be replaced. CMOS jumper might not be properly installed. Memory configuration is incorrect. 1 2

If the problem persists, replace the RTC battery. Set the date and time under Control Panel or in F10 Setup depending on the operating system. If the problempersists, replace the RTC battery.

164—Memory Size Error

1 2

Run Computer Setup (F10 Setup) or Windows utilities. Be sure memory module(s) (if any) are installed properly.

3

If third-party memory has been added, test using HP-only memory.

4

Verify proper memory module type.

124

SYSTEM DIAGNOSTICS AND TROUBLESHOOTING

Table 5-37 POST Error Messages (Continued)
ScreenMessage 183—Invalid Processor Jumper Setting 201—Memory Error Probable Cause System board jumper improperly set. Recommended Action

RAM failure.

1 2

Run Computer Setup (F10 Setup) or Windows utilities. Be sure that memory and continuity modules are installed correctly.

3 4

Verify proper memory module type. Remove and replace memory module(s) one at a time to isolate faulty module.5 6

Replace the faulty memory module(s). If error persists after replacing memory modules, replace the system board.

202—Memory Type Mismatch

Memory modules do not match each other.

Replace memory modules with matched sets.

Single Bit ECC error. 207—ECC Corrected Single Bit Errors in Memory Socket(s) y,y

1 2 3

Verify proper memory module type. Try another memory socket.Replace memory module if problem persists. Reseat the processor in its socket. If the processor does not respond, replace it. Verify proper memory module type. Try another memory socket. Replace memory with a module conforming to the SPD standard.

212—Failed Processor

Processor has failed to initialize.

1 2

213—Incompatible memory Module in memory Socket(s) X,X, X

A memory module inmemory socket identified in the error message is missing critical SPD information, or is incompatible with the chipset.

1 2 3

214—DIMM Configuration Warning 301—Keyboard Error

DIMMs not installed correctly (not paired correctly). Keyboard failure.

Refer to “Memory” on page 66 for the correct memory configurations and reseat the DIMMs accordingly. 1 2 3 4 Reconnect keyboard with workstationturned off. Check connector for bent or missing pins. Be sure that none of the keys are pressed. Replace keyboard. Reconnect keyboard with workstation turned off. Replace the system board. Reconnect the keyboard with workstation turned off. Be sure that none of the keys are pressed. Replace keyboard. Replace system board.

303—Keyboard Controller Error

I/O board keyboard controller.

1 2...