Amplificador Kicker

ZX

MULTI-CHANNELAMPLIFIER
ZX200.4
English Version
Versión Español
Amplificador del la Serie ZX.4
Manual del Propietario
Deutsche Version
Stereoverstärker der ZX.4-Serie
Benutzerhandbuch

©2006 Stillwater Designs

Version Française
Amplificateur de série ZX.4
Manuel d'utilisation

ZX.4SeriesAmplifier
Owner’sManual
FourChannelModel:
Congratulations on your
KICKER purchasePlease record your purchase
information and keep your sales
receipt for validation of warranty.

ZX200.4

Left Speaker AMP 1

-

Authorized Kicker Dealer: __________________________
Purchase Date:

Figure 2
Left Speaker AMP 2

+

-

+

+

-

+

Minimum impedance of 2 ohms per channel in stereo operation

-

Signal In AMP 2

24"
Or Less__________________________

(60cm)
Signal In AMP 1

Amplifier Model Number: __________________________
ZX200.4
Amplifier Serial Number:

Ground
Right Speaker AMP 2

Right Speaker AMP 1

Remote
Turn-On

__________________________

(45cm)

Installation . . . as easy as 1, 2, 3

+12V

Fuse

Battery

1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The amplifier’send-panel controls need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount theamplifier.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's
Use only one type of signal input to the amplifier,
either RCA Cable or Speaker Wire
Figure 1
chassis.
Speaker Wire
Use a twisted pair(s) ofRCA (low-level)
(High-Level
killers trk7“on Top”
Output)
interconnect cable to feed the audio signal to
RCA Cable
RCA Cable
the amplifier. If you are using only one pair of
(Low-Level)
(Low-Level)
AMP 1
AMP 2
RCA inputs, connect the RCA cable to the AMP
1 inputs. Push the fader button out, and all four
channels will work with a single pair of RCA
input cable. Push the fader buttonin, when
Fader Button: Push in for
using two pairs of RCA input cables. Keep the
2 pairs of inputs, push out
for a single pair of inputs.
RCA cable away from factory wiring harnesses
Left
+
Left
+
Speaker Wire
Left
and other power wiring. If you need to cross this
Speaker Wire
Left
(High-Level Input) Right (High-Level Input) Right AMP 1
Right +
wiring, cross it at a 90 degreeangle.
AMP 2
Right +
Only use speaker wire (high-level) inputs if
your source unit does not have RCA type outputs. If you are using only one pair of high-level inputs,
connect the speaker wire to the AMP 1 input. Push the fader button out, and all four channels will work
with a single high-level input cable. Push the fader button in, when using both sets of high-level inputs.
Install a fusewithin 18” (45cm) of the battery and in-line with the power cable connected to your
amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.
See the chart below for power and ground wire size, and fusing recommendations.
RCA
INPUTS

+--+OFF HI LO

R

+
Signal In AMP 2

-

+

24"
Or Less
(60cm)
Signal In AMP 1
Ground
Remote
Turn-On

HI-LEVEL
INPUT

XOVER

GAIN

AMP 1

-

+--+

L

R

XOVER

BASS

Figure 3
Minimum impedance of 4 ohms when in bridged operation

OFF HI LO

L

HI-LEVEL
INPUT

Mono Speaker AMP 2

GAIN
FADER

BASS

Mono Speaker AMP 1

AMP 2

(45cm)...