Manual Bios

MAIN | |
* System overview | * User enter (TAB) |
* System time | * Or ( shift – tab) to |
* System date | * Select a field |
* BIOS versión: P4VM800 BIOS P1.10 | * Use (+) or (-) to configure System time |
* Proccesor type: Intel (R) Pentium (R) 4 CPU 240 GHZ | |
* Processor speed: 2400MHZ | |
* Microcode update: F41/D | |
* Cache Size:1024 kb | |
* Total memory: 1024 MB With 64 mb shared memory | |
* DIMM1: 1024 mb 166 MHz ( DDR333) | |
* DIMM2: Mone | |
* | |
F1: general helpF9: load defaultsF10: save and exitEsc: exit | : Select screen : select item + - : change field Tab :select field |
BIOS SETUP UTILITY

ADVANCED
ADVANCED | |
Advancedsettings | * Configure the id device (S) |
Worning: setting wrong values in below sections may cause system to malfunction. * CPU: configuration | |
* CHIPSET: configuration | |
* ACPI : configuration | |
* IDE: configuration | |
* PCIPNP: configuration | |
* FLOPPY: configuration | |
* SUPER10 : configuration | |
* USB: configuration ||
| |
F1: general helpF9: load defaultsF10: save and exitEsc: exit | : Select screen : select item Enter go to sub screem |

CPU CONFIGURATION
CPU: configuration | |
* CPU Host Frequency (Auto) | * Select how to set the CPU host frequency. |
* Boot Failure Guard (Enabled) * Spead spectrum (Auto) | |
* RTM360-520 Skew setup (auto) | |
* CPU group delay ( Auto) | |
* CPU – CS group delay (Auto) | |
* 3V66 group delay ( Auto) | |
* PCI & CPI – F group deley (Auto ) | |
* DDR/SDRAM group delay (Auto ) | |
* PCI to 3v66 delay ( Auto ) * SDRAM – F group delay ( Auto) | |
| |
F1: general helpF9: load defaultsF10: save and exitEsc: exit |: Select screen : select item : change option |





CHIPSET configuration * CHIPSET Frequency (Auto) * DRAM CAS latency (Auto ) * DRAM BANK inter leave (Auto) * PRECHARGE to active (TRP) (Auto) * ACTIVE to DMD (TRCD9 (Auto) * REF to ACT/ REF toREF (TRFC) * ACT (O) to ACT (1) (Trrd) (Auto) * READ to precharge(TRTP) (Auto ) * WRITE to read CMD ( TWTR) (Auto ) * WRITE Recovery tome(TWTR) ( Auto ) * DRAM Command Rate (2T Comand) * DRAM Multiple page mode (Auto) * FLEXIBILITY OPTION (Disabled) * DRAM Voltage (Auto) * AGP Voltage ( Auto) | * Memory clock can be set by the code using auto or you can set one of the standard values. |
F1: general helpF9: load defaultsF10: save andexitEsc: exit | : Select screen : select item + - : change option |

ACIP CONFIGURATION
ACPI configuration ( Disabled) | |
* ACPI settings | * Select auto- detects or disabled the STR feature. |
* Suspend to RAM * Restore on AC/ POWER loss (power off) | |
* Ring – In power on (Disabled) | |
* PCIDevices power on (Disabled) | |
* PS/2 Key Board power on (disabled) | |
* RTC Alarm power on (disabled) | |
| |
| |
| |
| |
F1: general helpF9: load defaultsF10: save and exitEsc: exit | : Select screen : select item : change option |







IDE CONFIGURATION
IDEconfiguration (IDE) | |
* ON BOORD IDE controller (enabled) | |
* SATA Operation mode( RAID) * PRIMARY IDE MASTER (NOT Detected) | |
* PRIMARY IDE ALAVE ( HARD DISK) | |
* SECONDARY IDE MASTER (HORD DISK) | |
* SECONDARY IDE SLAVE (NOT DETECTED) | |
* SATA 1 ( NO DETECTED) * SATA 2 (NO DETECTED) | |
| |
| |
| |
| |
F1: general...