Manual de instalación de radio

Installation
Note:
• • • Check all connections and systems before final installation. Do not use unauthorized parts. The use of unauthorized parts may cause malfunctions. Consult with your dealer if installation requires drilling of holes or other modifications of the vehicle. Do not install this unit where: — it may interfere with operation of the vehicle. — it may cause injury to a passengeras a result of a sudden stop. The semiconductor laser will be damaged if it overheats. Install this unit away from hot places such as near the heater outlet. Optimum performance is obtained when the unit is installed at an angle of less than 60°. 1. Insert the mounting sleeve into the dashboard. • When installing in a shallow space, use a supplied mounting sleeve. If there is enough space behindthe unit, use factory supplied mounting sleeve. 2. Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place. 3. Install the unit as illustrated.

ENGLISH
DIN Rear-mount
1. Extend top and bottom of the trim ring outwards to remove the trim ring. When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upsidedown, the trim ring will not fit properly.) • It becomes easy to remove the trim ring if the front panel is released. Trim ring

MANUEL D’INSTALLATION

INSTALLATION MANUAL

•

Removing the Unit
1. Extend top and bottom of the trim ring outwards to remove the trim ring. When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upsidedown, the trim ring will not fit properly.) • It becomes easy to remove the trim ring if the front panel is released. Trim ring

•

DEH-P6950IB

•

60°

2. Determine the appropriate position where the holes on the bracket and the side of the unit match.

•

When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel andwrap any loose cables so they are not blocking the vents.

2. Insert the supplied extraction keys into both sides of the unit until they click into place. 3. Pull the unit out of the dashboard.

DIN Front/Rear-mount
This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unitchassis). For details, refer to the following installation methods.

3. Tighten two screws on each side. • Use either truss screws (5 mm × 8 mm) or flush surface screws (5 mm × 9 mm), depending on the shape of screw holes in the bracket. Screw

This product conforms to new cord colors. Los colores de los cables de este producto se conforman con un nuevo código de colores. As cores dos fiosdeste produto seguem um novo padrão de cores.

DIN Front-mount
Installation with the rubber bush
Dashboard
182 182

Æ…b¹b'« „öÝô« Ê«uë lÄ “UN'« «c¼ r− M¹

Mounting sleeve Factory radio mounting bracket Rubber bush

Dashboard or Console

53

Screw

Printed in Thailand

ES



Instalación
Nota:
• • Verifique todas las conexiones y sistemas antes de la instalación final. Noutilice piezas no autorizadas. El uso de piezas no autorizadas puede causar un fallo de funcionamiento. Consulte su revendedor si se requiere taladrar agujeros o hacer otras modificaciones del vehículo para la instalación. No instale esta unidad donde: — pueda interferir con la operación del vehículo. — pueda causar lesiones a un pasajero en el caso de una parada brusca. El láser semiconductor sedañará si se sobrecalienta. Instale esta unidad alejada de lugares calientes como cerca de la salida del calentador. Se obtiene el rendimiento óptimo cuando se instala la unidad en un ángulo inferior a 60°. 1. Inserte el manguito de montaje en el tablero de instrumentos. • Cuando instale en un lugar poco profundo, utilice el manguito de montaje suministrado. Si hay espacio suficiente detrás de la...