Setup Of Multivoip Mvp410-Cf And Mvp810-Cf

README
Doc# 82051303L 05/11/06

for Setup of MultiVOIP MVP410-CF and MVP810-CF, CallFinders built on MultiVOIP Platform

This document describes a special interim version of Multi-Tech CallFinder products (MVP410-CF and MVP810-CF) that have been built on the platform of the corresponding analog MultiVOIP products (MVP410 and MVP810). The term “MVP-CF” will be used when referring collectivelyto both the MVP410-CF and the MVP810-CF.

Labeling of MVP-CF Cable Receptacles & Signal Channels
The MVP410-CF has four channels and the MVP810-CF has eight channels. For each channel, there are two cable receptacles on the MVP unit. The larger receptacle, which is for E&M telephony (using RJ-45 connectors), is not used. The smaller receptacle, marked “FXS/FXO,” is used and it accommodatesRJ-11 connectors. The FXS/FXO receptacle can be connected to either (a) an analog DID line, or (b) the central-office Line port of a PBX, or (c) the analog station-port of a PBX. 1. Connect analog DID lines to the odd-numbered channels of the MVP unit (channels 1 & 3 of the MVP410-CF; channels 1, 3, 5, & 7 of the MVP810-CF). Use the FXS/FXO receptacle for each channel. 2. Even-numbered channels(channels 2 & 4 of the MVP410-CF; channels 2, 4, 6, & 8 of the MVP810-CF) will be used either as an FXS interface or as an FXO interface, depending on what that channel is connected to. If the channel is connected to a line port of a PBX, set the channel to FXS. If the channel is connected to the analog station port of a PBX, set the channel to FXO. 3. When a PBX line port is connected to the MVPchannel, the FXS interface is used. DTMF digits coming in on this channel will be routed to an auto-attendant listening on the line port. 4. When a PBX analog station port is connected to the MVP channel, the FXO interface will be used and DTMF will be routed to direct extensions of the PBX.

CallFinder on MultiVOIP Platform README Document

Page 1 of 4

Technical Configuration Procedure
1.Turn on the power of the MVP-410/810-CF unit and wait for the boot light to go out. 2. The Command Cable has a DB25 connector at one end and it connects to the Command port on the MVP unit. The other end is a DB9 connector and it connects to the computer you are using to configure the MVP unit. NOTE: Because USB-to-Serial adapters sometimes cause problems, we recommend using a standard built in DB9serial port when available. 3. Install the MultiVOIP software on the computer that you’ll use to configure the MVP unit. You will be asked to designate an available COM port on your PC that your PC will use to communicate with the MVP unit. When prompted to ‘Do you want to run the MultiVOIP configuration’, click Yes. 4. After the configuration of the MVP unit has been read into the PC, the Statusat the bottom right corner of the screen will be “Rights: Read/Write.” 5. In the MultiVOIP software, go to Configuration | Ethernet/IP. a. Enter IP Address. b. Enter IP Mask. c. Enter Gateway IP. d. Click OK. 6. In the MultiVOIP software, go to Configuration | Voice/Fax. a. In the Selected Coder field, choose “G.711 u-law.” b. In the Advanced Features group, uncheck “Silence Compression.” c. Clickon the Copy Channel button. When the Copy Channel screen appears, click “Copy to All.” 7. In the MultiVOIP software, go to Configuration | Interface. You will configure Channel 1 first and copy its configuration to all odd-numbered channels. Then you will configure Channel 2 and copy its configuration to all even channels. a. Set the Interface Type field to “DID/DPO.” b. In the DID Options fieldgroup, set the Start Modes field to “Wink Start.” c. Click on the Copy Channel button. When the Copy Channel screen appears, select the odd channels (3, 5, and 7). Click Copy. Click OK. d. In the Interface Parameters screen, in the Select Channel field, select “Channel 2.” e. Set the Interface Type field to FXS or FXO. If the channel is connected to a line port of a PBX, set the channel to FXS....