Tareas

Steebar’s Original
APPLICATION INSTRUCTIONS
BAR & TABLE TOP HIGH GLOSS EPOXY COATING
1 TO 1 BY VOLUME: IMPORTANT: Read this entire insert before using this epoxy
For interior surfaces & commercial use only. Do not use outside.
WARNING – Fatal or harmful if swallowed – If resin side is swallowed, induce vomiting and CALL A PHYSICIAN Dilute by giving water or
milk to drink if victim isconscious. IMMEDIATELY. If hardener is swallowed, DO NOT INDUCE VOMITING. GET MEDICALATTENTION
IMMEDIATELY. If combined mixture is swallowed, DO NOT INDUCE VOMITING. Dilute by giving water or milk to drink if victim is
conscious. GET MEDICAL ATTENTION. SEVERE EYE IRRITANT – in case of eye contact, flush with water for ten minutes and seek prompt
medical attention. SKIN – Resin and hardener are skinirritants and may cause allergic reaction. Protective clothing, including plastic
gloves, should be worn while handling this compound. If POLYMER accidentally comes in contact with skin, wash affected areas with soap and
water immediately. AVOID INHAL-ATION – Use in well ventilated areas. The compound left in mixing cup more than 2 minutes will cause heat.
Resin contains epoxy bisphenol, aresin. Hardener contains a polyamine curing agent. Polymer should be used only by adults or under close
supervision by an adult. KEEP OUT OF REACH OF CHILDREN.
WARNING – Before starting on your project, we strongly suggest you do a test piece to help you become familiar with this type of product,and for
you to decide whether this will be the right product for the type of project you are doing. We donot recommend using THIS PRODUCT on“Fine
Furniture.” Steebar’s Original - Sets up in about 4 hours and is cured to touch in 24 hours. One coat is usually all that is needed to capture a
glossyshine. Two or more coats may be applied without damaging the first coat. Steebar’s original is recommended for interior use only.
STORAGE – The epoxy should be stored in a dry place between 75ºF to 80ºFand out of the reach of children. Resin and hardener should not
be left in an open container. Steebar’s original should be used in a room where the humidity is under 60%. This product should be used within
oneyear of purchase.
TOOLS – Mixing containers – should have a smooth, flat bottom and be clean and dust free.
Stick – Must have flat, straight edge to ensure thorough mixing.
Brush –Sometimes a small brush is needed for coating edges of crevices.
COVERAGE - Mix only the amount of Steebar’s original that you need at one time. Unused resin and hardener should be left in original containers.
After pouring, you have about 20 minutes working time before the epoxy begins to harden. Coverage for pour coat at (1/16 inch) =
1 oz. of the epoxy will cover 37 square inches
pint kit willcover approximately 2 square feet
Pint kit will cover approximately 4 square feet
Quart kit will cover approximately 8 square feet
Gallon kit will cover approximately 35 square feet
NOTE: Pouring over a thickness of 1/16 inch may cause excessive bubbles, yellowing, and distortions in surface. Use multiple coats to
achieve desired thickness. Please subtract for losses over edge of tables and barnose.
SURFACE TO BE COVERED
1) For best results, the surface to be covered must be dry and free of dust, wax, grease or oil.
2) The item to be coated should be about 2 inches above the work area so that the extra mixture will drop off the item. It is a good idea to put a
newspaper or a drop cloth under the item to catch the drips.
3) Apply tape or paste wax now to prepare the back surface ofthe project for easy drip removal.
SEAL COATS – Porous materials require what is called a seal coat in order to prevent air from escaping into the fluid. To seal coat, use _ of the
epoxy you would normally use for a flood coat. Brush a thin coat on the item. Wait about 12 hours and then you are ready to apply the flood coat. A
white glue seal coat can also be used. Mix 4 parts white glue to...