Desmontar Xbox360

Installing Xbox 360 Motherboard Replacement
Tools used in this guide
Metal Spudger Set
Small Flathead Screwdriver
Spudger
T8 Torx Screwdriver
T10 Torx Screwdriver
Xbox 360 Opening Tool
Installing Xbox 360 Motherboard Replacement
© 2010 iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 26
Step 1 - Hard Drive
Grasp the hard drive assembly and press the release
button while lifting its frontedge.
Remove the hard drive assembly from the top vent.
Step 2 - Bottom Vent
Stand the console vertically with the bottom
edge facing up.
Insert the flat end of a spudger or the edge of an Xbox
360 opening tool into the small gap at the front edge of
the bottom vent.
Pry the front edge of the bottom vent away from the
faceplate.
Installing Xbox 360 Motherboard Replacement
© 2010 iFixit— CC BY-NC-SA www.iFixit.com Page 2 of 26
Step 3
In the next few steps, you will use the tip of
a spudger or the finger of an Xbox 360
opening tool to release the clips along the
left and right sides of the bottom vent. Their
locations are highlighted in red.
Step 4
To release the clips, work from the front edge of the
bottom vent.
While slightly lifting the front edge of the bottomvent,
use the tip of a spudger to push the clips closest to the
front of the bottom vent towards the inside of the
console.
Installing Xbox 360 Motherboard Replacement
© 2010 iFixit — CC BY-NC-SA www.iFixit.com Page 3 of 26
Step 5
Repeat the same process to release the two center
clips on the bottom vent.
Step 6
Use the tip of your spudger to release the clips on the
bottom vent nearestthe back of the Xbox.
Installing Xbox 360 Motherboard Replacement
© 2010 iFixit — CC BY-NC-SA www.iFixit.com Page 4 of 26
Step 7
Remove the bottom vent from the 360.
Step 8 - Faceplate
Insert the edge of a spudger between the faceplate and
the outer casing near the power button.
Run your spudger along the edge of the faceplate to
release the clips securing it to the front of the console.Installing Xbox 360 Motherboard Replacement
© 2010 iFixit — CC BY-NC-SA www.iFixit.com Page 5 of 26
Step 9
Repeat the same motions as previously mentioned to
release the left side of the faceplate.
Step 10
Remove the faceplate from the front face of the console.
Installing Xbox 360 Motherboard Replacement
© 2010 iFixit — CC BY-NC-SA www.iFixit.com Page 6 of 26
Step 11 - Top Vent
Stand theconsole vertically with the top
edge facing up.
The top vent is secured to the console via clips. The
first two clips are located underneath the top vent
closest to the faceplate, as shown in the pictures.
Step 12
Insert the flat end of a spudger into the small gaps
previously mentioned to release the clips.
Installing Xbox 360 Motherboard Replacement
© 2010 iFixit — CC BY-NC-SAwww.iFixit.com Page 7 of 26
Step 13
In the next few steps, you will use the tip of
a spudger or the finger of an Xbox 360
opening tool to release the clips along the
left and right sides of the top vent. Their
locations are highlighted in red.
Step 14
To release the clips, work from the middle of the top
vent.
While slightly lifting the front edge of the top vent, use
the tip of a spudger topush the clips closest to the
center of the top vent towards the inside of the console.
Installing Xbox 360 Motherboard Replacement
© 2010 iFixit — CC BY-NC-SA www.iFixit.com Page 8 of 26
Step 15
Use the tip of your spudger to release the clip on the
top vent nearest the back of the Xbox's upper case.
Step 16
The last clip is hidden underneath the
rubber foot nearest the back of theconsole.
Use the tip of your spudger to release the clip on the
top vent nearest the back of the Xbox.
Remove the top vent from the 360.
Installing Xbox 360 Motherboard Replacement
© 2010 iFixit — CC BY-NC-SA www.iFixit.com Page 9 of 26
Step 17 - Lower Case
To continue, you must peel the warranty
sticker off the console. Be aware that this
will void your console's warranty agreement
with...