Enrutamiento evaluacion basada en aptitudes ospf

Exploration Routing: EIGRP Skills Based Assessment -Answered

Learning Objectives
Upon completion of this lab, you will be able to: • • • • • • • • • Subnet an address space with given requirements Assign appropriate addresses to interfaces and document them in the address table below Cable the network according to the diagram Erase the startup configuration and reload a router to the defaultstate. Configure EIGRP routing on all routers. Configure and propagate a default static route. Verify EIGRP operation. Test and verify full connectivity. Reflect upon and document the network implementation.

Scenario
In this lab, you will be given a summarized address which you will use to create an efficient addressing scheme to accommodate all hosts on the network. A combination of EIGRP anda static default route will be

All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 1 of 4

CCNA Exploration Routing Protocols and Concepts

Exploration Routing: EIGRP Skills Based Assessment

required so that hosts on networks not directly connected can communicate. You have completed this lab when each hostcan ping the each other.

Task 1: Create an Addressing Scheme.
Step 1: Use the 192.168.156.0/22 address to create an addressing scheme to accommodate all hosts on the network. Begin the address assignments with the 192.168.157.0 address. Document all subnet addresses in Table 1. Table 1 Device HQ Interface Fa0/0 Fa0/1 S0/0/1 S0/0/0 Fa0/0 Fa0/1 S0/0/1 Fa0/0 Fa0/1 S0/0/0 Number of Hosts 90 /25 60/26 2 /30 2 /30 30 /30 60 /26 2 /30 128 /24 60 /26 2 /30 Subnet Subnet Mask

Remote1

Remote2

192.168.158.0 192.168.158.12 8 192.168.159.96 192.168.159.10 0 192.168.159.64 192.168.158.19 2 192.168.159.96 192.168.157.0 192.168.159.0 192.168.159.10 0

255.255.255.128 255.255.255.192 255.255.255.252 255.255.255.252 255.255.255.224 255.255.255.192 255.255.255.252 255.255.255.0255.255.255.192 255.255.255.252

Step 2: Document router interface and PC addresses in Table 2. Assign the last usable IP address of each subnet to each PC. Table 2 Device HQ Interface Fa0/0 Fa0/1 S0/0/1 S0/0/0 Lo0 Fa0/0 Fa0/1 S0/0/1 Fa0/0 Fa0/1 S0/0/0 Ethernet Ethernet Ethernet Ethernet Ethernet IP Address 192.168.158.1 192.168.158.129 192.168.159.97 192.168.159.101 189.54.69.254 192.168.159.65192.168.158.193 192.168.159.98 192.168.157.1 192.168.159.1 192.168.159.102 192.168.158.126 192.168.158.190 192.168.159.94 192.168.158.254 192.168.159.62 Subnet Mask 255.255.255.128 255.255.255.192 255.255.255.252 255.255.255.252 255.255.255.252 255.255.255.224 255.255.255.192 255.255.255.252 255.255.255.0 255.255.255.192 255.255.255.252 255.255.255.128 255.255.255.192 255.255.255.224 255.255.255.192255.255.255.192 Default Gateway 0.0.0.127 0.0.0.63 0.0.0.3 0.0.0.3 0.0.0.3 0.0.0.31 0.0.0.63 0.0.0.3 0.0.0.255 0.0.0.63 0.0.0.3 192.168.158.1 192.168.158.129 192.168.159.65 192.168.158.193 192.168.159.1
Page 2 of 4

Remote1

Remote2 PC1 PC2 PC3 PC4 PC5

All contents are Copyright © 1992–2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

CCNA ExplorationRouting Protocols and Concepts

Exploration Routing: EIGRP Skills Based Assessment

PC6

Ethernet

192.168.157.254

255.255.255.0

192.168.157.1

Step 3: Cable and configure the network based on the diagram and the addressing scheme you created in the previous step. Assign the last usable host address of each subnet to each PC. Instructor’s Initial ______

Task 2: Configure EIGRP withProcess ID 1 using Wildcard Masks.
Step 1: Configure EIGRP on the HQ router and advertise all directly connected networks except the loopback interface. Advertise the network along with a wildcard mask for the appropriate subnet. Step 2: Configure EIGRP on the Remote1 router and advertise all directly connected networks. Advertise the network along with a wildcard mask for the appropriate...