Priemra prueba

SITEMANAGER 3134
The SiteManager requires being able to access the Internet via the Uplink port in order to target a GateManager server. By default it will receive its IP address by DHCP, and you only need to configure the Uplink if you will use a fixed IP. Additionally You must configure the GateManager settings into the SiteManager.

INITIAL SETUP
3.

Using the Secomea Appliance Launcher.a. b. Download and install the Appliance Launcher tool from here: http://info.secomea.com/appliance-launcher. Connect the DEV1 port of the SiteManager to the local network and power it on. The SiteManager must be on the same Subnet as your PC. Alternatively connect the SiteManager with an Ethernet cable directly to your PC. Power on the SiteManager and wait approx. 1 minute for it to becomeready. Start the Appliance Launcher and the SiteManager should be listed in the first screen. If it does not appear immediately, try pressing the Search button a couple of times. Follow the Wizard and set the UPLINK address if you want to use a fixed IP address.

A.

Applying UPLINK settings for accessing the Internet

c. d.

Select one of the following 3 methods: 1.

Using a DHCP server
a.b. c. d. e. f. g. Connect the UPLINK port of the SiteManager to your local network and power it on. After approx. 1 minute the SiteManager should have received an IP address from your DHCP server. Check the lease list of the DHCP server to see what the IP address is. Type the IP address in your web browser preceded with https:// (e.g. https://172.168.41.13). Login with login admin and passwordadmin. Enter menu System --> Uplink to set the UPLINK address if you want to set a fixed IP address.. Continue with section B to configure GateManager settings. 3. 2. 1. B.

e.

Applying settings for connecting to a GateManager server
In the SiteManager Web GUI enter the menu GateManager --> General (if using the Appliance Launcher, follow the wizard to the GateManager Parameters page). Enterthe IP address of the GateManager server that the SiteManager should connect to, and a Domain Token for the domain where the SiteManager should appear. You should have received this information from your administrator or from where you received the SiteManager. When the settings are entered, you should reboot the SiteManager. Observe that the Status LED goes steady Green, which indicates that theSiteManager is connected to the GateManager. Once attached to the GateManager, you can use the GateManager Console or a LinkManager Client to get remote access to the SiteManager Web GUI to perform additional configuration (DEV ports, Agents etc.) For additional documentation refer to : http://info.secomea.com/quick-start Detailed guides, new firmware etc. can be downloaded from Secomea’s partnerpage: http://info.secomea.com/RDM-Documentation. You will be prompted to login. If you do not already have a login, you can sign up using the link at the bottom of the login page.

2.

Using the default IP address (10.0.0.1)
a. b. c. d. e. f. g. Connect the DEV1 port of the SiteManager to the Ethernet port of your PC using a standard Ethernet cable. Configure your PC’s Ethernet adapter to10.0.0.2 subnet mask 255.255.255.0. Power on the SiteManager and wait approx. 1 minute for it to become ready. Type the following in your web browser: https//10.0.0.1 Login with login admin and password admin. Enter menu System --> Uplink to set the UPLINK address if you want to use a fixed IP address. Continue with section B to configure GateManager settings.

4.

5. 6.

HARDWARE SPECIFIC
C.NICE TO KNOW
F.

LED signaling

IO Ports

Refer to the following table. GM denotes GateManager, and LM denotes LinkManager. The Power LED is steady Green when power is supplied. State Booting GM Connecting or Disconnected GM Connected GM Configuration Missing/Invalid or Uplink settings Missing/Invalid LM Connected Remote Management disabled (via INPUT1 or SiteManager GUI) Ready Green...