Tareas

National Parts Distributing Ltd
presents

trouble shooting tips
for
Service Station Maintenance

Index
TST 1
TST 2
TST 3
TST 4
TST 5
TST 6
TST 7
TST 8
TST 10
TST 11
TST 12
TST 13
TST 14
TST 15
TST 16
TST 17
TST 18
TST 19
TST 20
TST 21

Gilbarco Pump Error Codes
Fluorescent’s and You!
Re-Occurring problems on Gilbarco Modular Pumps
The Hot Black Head
The NoisyPump That Does Not Pump
Gilbarco Pump/Dispenser Resets
T16226-G Main Display Jumper Settings
That darn Gilbarco Code 34
code 31 or 35"
Turn off that Power!
Kraus Type A and B Skil 184 Software Swapping
Dead Batteries on Gilbarco TCR-G2 Memory Expansion Boards
Kraus Micon 200 Boards Modified for Back Light
Those Bugs Bite
Sealing D&H Pulsers to Prevent Water Wicking up Shaft
InstallingDG8340 Esco Printers with Gilbarco Transac Consoles
Esco Genesis and D&H EQ30 Heads Pulse Rates
C2000-K Consoles with Kraus Micon & MTI (D&H ) EQ30 - issues
SKIL 409A3 Kraus I.S. Switch Assembly
Totalizer Readings from Kraus Micon 100, 200 and 500 and MTI
(D&H) EQ30 Retrofit Heads and Progressive International C2000-K
Installing Progressive International C2000 Consoles

Page 1 to 12
Page 13to 14
Page 15
Page 16
Page 17 to 23
Page 24
Page 25
Page 26 to 27
Page 28
Page 29
Page 30
Page 31
Page 32
Page 33
Page 34
Page 35 to 36
Page 37
Page 38 to 39
Page 40
Page 41
Page 42

trouble shooting tips
No. 1 Gilbarco Pump Error Codes
This first of our "trouble shooting tips" was originally published in 1988 and since that time we have
discovered some errors that we made,plus we have learned of some new codes which have been added
since that time, therefore we are now updating and reissuing the "tip".
It should be noted to avoid any confusion this bulletin is a summary of all the various codes that we
at ERI are aware of, and are our interpretation of those codes.
While we are going to summarize the Codes in this bulletin along with the causes of the Errors,we
will be dealing with some of these in greater detail in future "trouble shooting tips".
There are three basic generations of logic development in Gilbarco pumps and we will detail each
generation in succession in this "tips".
IT SHOULD BE NOTED THAT THESE ERROR CODES SHOW UP ON THE PRICE PER UNIT
DISPLAY OF THE PUMP ITSELF! They do not show up on the Console except for the Transac 12G.
ITSHOULD ALSO BE NOTED THAT THE "ERROR CODE" WILL BE FLASHING BACK AND
FORTH WITH THE PRICE SET ON THE PUMP.
All of the "Error Codes" will stop the pump from operating and some will result in loss of
communication with the older Consoles. i.e. When the operator selects the pump on the Console
it will not be there!

IMPORTANT!!!!!! - TURN OFF POWER TO THE PUMP (AFTER ISOLATING
IT ON SELFSERVE SYSTEMS) BEFORE CHANGING ANY COMPONENTS IN
THE PUMP
You should carry out trouble shooting in the order that we detail it, from "over the phone to highest
number. In other words easiest and most likely to most difficult & least likely.

FIRST GENERATION: 8080 LOGIC BUILT FROM DAY 1 TO FALL OF 1985 IN
HIGHLINE 111B AND TO FALL OF 1987 IN MULTI PRODUCT. (DOES NOT
APPEAR IN SALESMAKER 4) INALL RETROPAC COMPUTERS.
This generation only had two (2) "error codes".
1. FLASHING "PRICE" THEN "BLANK" (DISPLAY GOES OUT) THEN THE "PRICE" AGAIN,
AND SO ON.
DESCRIPTION OF PROBLEM: A Pulsing System failure. It can happen on only one hose or on
all hoses on a pump. It is important to find out "over the phone" if it is occurring on one hose
Page 1

trouble shooting tips
only, or on allhoses.
CAUSES: ONE HOSE ONLY
- A power spike.
- A bad plug connection or moisture on a connection.
- A faulty Pulser.
- A faulty Barrier.
- A break in wiring to the Pulser.
CAUSES: ALL HOSES (Multi Product Pumps it may be only all the hoses on one side, all the time.)
- Faulty Power
- Faulty Regulator/Interface Board. (These are separate boards on a Multi Product.)
CURES: OVER THE PHONE...