Ayuda con instalacion de hackintosh en h55 y i5

iBoot + MultiBeast: Install Mac OS X on any Intel-based PC
Posted by tonymacx86 on Monday, April 12, 2010
Labels: Core i3, Core i5, Core i7, guide, H55, iBoot, Mac, MultiBeast, OS X, P55, Snow Leopard, Video, X58

Any OSx86 installation guide can seem daunting at first glance, especially when trying to remember cryptic terminal commands and sorting through volumes of misinformation on theweb.  This guide requires no coding, terminal work, or Mac experience of any kind.  You will not need access to a Mac.  In fact, it's easier and faster for me to install Snow Leopard with fully working components on my system than it is to install Windows 7.  And more fun.

The iBoot + MultiBeast method is designed and tested for any desktop or laptop running the latest line of Intel processors,the Core i3/i5/i7s.  I have had reports of success with older machines as well including CoreDuo, Core2Duo, and even Pentium 4.  However, AMD processors are not supported.

YOU WILL NEED
* A computer running an Intel Processor
* A blank CD
* A Mac OS X Snow Leopard Retail DVD
* To leave any fear of your computer at the door.
* Patience and humility- it may not work outperfectly the first time- but with enough tenacity and grit, you'll reach the promised land.  It's easy to get frustrated, but don't give up!  There are a community of users with similar hardware in the tonymacx86 Forum to provide support if you get stuck.
BEFORE YOU BEGIN
* If you have greater than 4gb of RAM, remove the extra RAM for a maximum of 4gb.  You can put back any extra RAM in after theinstallation process.
* Use only 1 graphics card in the 1st PCIe slot with 1 monitor plugged in.
* Remove any hard drives besides the blank drive being used for OS X.
* Remove any USB peripherals besides keyboard and mouse.
* Remove any PCI cards besides graphics- they may not be Mac compatible.
* If using a Gigabyte 1156 board, use the blue Intel SATA ports- not the whiteGigabyte SATA ports.
* It's best to use an empty hard drive- you will have to partition and format the drive. 
* Always back up any of your important data.
STEP 1: BIOS SETTINGS
You will need to set your BIOS to ACHI mode and your Boot Priority to boot from CD-ROM first.  This is the most important step, and one many people overlook.  Make sure your bios settings match these.  It's notdifficult- the only thing I did on my Gigabyte board besides setting Boot Priority to CD/DVD first was set Optimized Defaults, change SATA to AHCI mode, and set HPET to 64-bit mode.

STEP 2: INSTALL MAC OS X 
In order to boot the Mac OS X Retail DVD, you'll need to download and burn iBoot.  For desktops and laptops using unsupported Intel CPUs and graphics, a legacy version of iBoot can bedownloaded here.

1. Download iBoot
2. Burn the image to CD
3. Place iBoot in CD/DVD drive
4. Restart computer
5. At boot prompt, eject iBoot

6. Insert your Mac OS X Snow Leopard Retail DVD and press F5
7. When you see the screen below, press enter to begin the boot process

8. When you get to the installation screen, open Utilities/Disk Utility.  NOTE: If you cannot get tothe installation screen, retry from Step 4, type PCIRootUID=1 before hitting enter. If that doesn't work then try PCIRootUID=1 -x or just -x which will enter Mac OS X Safe Mode and will allow you to proceed.
9. Partition your hard drive to GUID Partition Table
10. Format your hard drive to Mac OS Extended (Journaled).   NOTE: The bootloader can only boot from a disk or partition of 1 TBor less.  Partition larger drives.
11. For the purposes of this guide, name it Snow Leopard.  You can rename it later.
12. Close Disk Utility
13. When the installer asks you where to install, choose Snow Leopard
14. Choose Customize‚ and uncheck additional options.  This will hasten the install process.  You can always install this stuff later.
15. Restart computer.
16....