Chrysler-Dodge Radio Wire Harnesses
Majority Of Vehicles
Pin What It Is
A B C D E F G
Typical Dodge/Chrysler In Dash Wire Color
Typical New Radio Equivalent Wire Color
H I J K L M N
Gray Plug AS VIEWED FROM MATING END OF CONNECTOR
A Right Rear Spkr (-) Blue w/ White Stripe Purple w/ Black Stripe B Left Rear Spkr (-) Brown w/ Yellow Stripe Greenw/ Black Stripe C Right Front Spkr (+) Purple Gray D Left Front Spkr (+) Dark Green White E Right Rear Spkr (+) Blue w/ Orange Stripe Purple F Left Rear Spkr (+) Brown w/ Blue Stripe Green G Power Antenna/Amp White (use for Infinity Radio) Blue H +12 Volt Battery Wire Pink or Pink w/ White Stripe Yellow I +12 Volt Ignition Wire Red w/ White Strip Red J Radio Dimmer Wire Do Not Use K HeadlightDimmer Wire Do Not Use L Right Front Spkr (-) Blue w/ Red Stripe Gray w/ Black Stripe M Left Front Spkr (-) Brown w/ Red Stripe White w/ Black Stripe N No Wire Metal Braid Or Plastic Connector Attached To Back Of Radio Is The Ground Wire Black (see TIP)
If your original radio had a braided strap bolted to the rear of the radio.
Crimp a ring terminal to the new radios ground wire andinsert a bolt through both connectors to connect the ring terminal of the braided ground wire to the ring terminal attached to the new radios ground wire.
If your original radio had a plastic connector containing a single wire plugged into the rear of the radio.
Crimp a male tab spade to the new radios ground wire. Slide it into the female tab spade connector that had originally snappedinto the rear of the factory radio.
If your original radio or speaker grills were labeled or marked with ‘INFINITY’
Crimp a male tab spade to the new radios ground wire. Slide it into the female tab spade connector that had originally snapped into the rear of the factory radio to ground the Infinity amp and activate the ‘Infinity’ sound system.
Note: using an optional snap on wireharness adapter will simplify the wiring. Most snap on wire harness adapters have already converted and color coded the wires from the auto makers in dash wire harness to match typical aftermarket radio wire colors. ** The wire colors listed in the chart above are typical for these vehicles during these years but may not be the exact colors for this vehicle. This is another reason to use a snap onwire harness adapter. **
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized In Writing By The Install Doctor Is Prohibited. Protected By U.S. Copyright Laws. © 1997,1998,1999,2000.
All Information, Including Photos And Illustrations, In These Pages Is Believed To Be Correct And Reliable. The Information Contained In These Pages Is Given As GeneralInformation For The Installation Of Audio, Video, Security, Communications, And Other Accessory Products Into Mobile And/Or Vehicle Applications. The Install Doctor, Any Subsidiaries Or Divisions Thereof, Or Any Member Of These Companies Shall Not Be Held Liable For Any Damages And/Or Injuries Resulting From The Use Of Information Contained In These Pages. All Information Contained In These Pages Should BeChecked And Verified With Appropriate Test Equipment To Assure The Safety And Proper Operation Of Equipment Installed And The Vehicle Itself. Careful Attention Should Be Given To All Electronic/Electric Circuits. High Voltages And Currents Can Cause Bodily Injury, Skin Damage, And Even Death. Installs Are Taken At The Risk Of Each Installer, And/Or Individual.
www.installdr.comChrysler-Mitsubishi Radio Wire Harnesses
2-pc Joint Production Vehicles
Pin What It Is Mitsubishi-Chrysler Corp In Dash Wire Color Typical New Radio Equivalent Wire Color A Right Front Speaker (+) Two White w/ Red Stripe Gray B Right Rear Speaker (+) Yellow w/ Red Stripe Purple C Do Not Use D Left Front Speaker (+) Two White w/ Blue Stripe White E Left Rear Speaker (+) Yellow w/ Blue Stripe Green F Light...