Teoria

ENetwork Basic Configuration PT Practice SBA
A few things to keep in mind while completing this activity: 1. Do not use the browser Back button or close or reload any Exam windows during the exam. 2. Do not close Packet Tracer when you are done. It will close automatically. 3. Click the Submit Assessment button to submit your work.

Introduction
In this practice Packet Tracer Skills Exam, youwill: • • • finish connecting the devices design and implement an addressing scheme to meet stated requirements configure, verify, and troubleshoot connectivity between all devices in the network

Addressing Table
Device Interface Fa0/0 Router1 Fa0/1 Switch1 PC1 PC2 VLAN1 NIC NIC 172.16.1.33 172.16.1.2 172.16.1.30 172.16.1.46 255.255.255.240 255.255.255.224 255.255.255.224 255.255.255.240 n/a172.16.1.1 172.16.1.1 172.16.1.33 Address 172.16.1.1 Subnet Mask 255.255.255.224 Default Gateway n/a

NOTE: The initial network has some errors. To aid in configuring and verifying the devices as well troubleshooting the existing errors, use a printed version of these instructions to fill in the missing address information in the table during Step 2.

Step 1: Connect the Devices.
Connect thefollowing devices using the appropriate cable: a. Connect PC1 to Switch1. b. Connect Switch1 to the Fa0/0 interface on Router1. c. Connect Switch2 to the Fa0/1 interface on Router1. d. Connect PC1 to the Router1 console port.

Step 2: Determine the IP Addressing Scheme.
Design an addressing scheme and fill in the Addressing Table based on the following requirements: a. Subnet the address space172.16.1.0/24 to provide 30 host addresses for LAN 1 while wasting the least amount of address space. b. Assign the first available subnet to LAN 1. c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on Router1. d. Assign the second address in this subnet to the VLAN 1 interface on Switch1. e. Assign the highest (last) host IP address in this subnet to PC1. f. Usingthe next available subnet, further subnet it to provide 10 host addresses for LAN2 while wasting the least amount of address space.

g. Assign the lowest (first) host address in the LAN2 subnet to the Fa0/1 interface on Router1.

Step 3: Configure Router1.
a. Configure Router1 with the following basic parameters: • • • • The router name is Router1. The privileged EXEC mode uses the followingencrypted password: class Enable Telnet and console line login using the following password: cisco Configure the banner message-of-the-day as Authorized access only!

b. Configure the two Fast Ethernet interfaces, including addressing and a description. c. Close the terminal window after completing the router configuration.

Step 4: Configure Switch1 and Verify Connectivity.
a. Remove theconsole connection between PC1 and Router1. b. Connect PC1 to the Switch1 console port. c. Configure Switch1 with the following basic parameters: • • • • The switch name is Switch1 The privileged EXEC mode uses the following encrypted password: class Enable Telnet and console line login using the following password: cisco Configure the banner message-of-the-day as Authorized access only!

d.Configure interface VLAN 1 and default gateway for Switch1. e. Switch1 should be able to ping the default gateway.

Step 5: Configure and Verify PC1 Addressing.
a. Using the IP addressing you determined in Step 2, configure PC1 with the correct addressing. b. PC1 should be able to ping the default gateway.

Step 6: Verify and Troubleshoot End-to-End Connectivity.
Verify that PC1 is able to pingPC2. If the ping fails, locate and correct any errors. For example, make sure PC2 is configured correctly with appropriate addressing for the subnet it belongs to.
Version 1.0 Created in Packet Tracer 5.2.1 and Marvel 1.0.1 All contents are Copyright © 1992 - 2010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

             

Activity Topology and...