Proyecto esquinero

Project 16912EZ:

Tapering Corner Whatnot Shelf
While the tapering structure of this pine corner shelf poses a challenge, you’ll have no problem putting the piece together once you understand its angular construction.

Corner Shelf Materials List
Part A B C D E F G H I J K L M N O P Q R Description Side (upper) Back Back Support Top Top Shelf Middle Shelf Lower Shelf Bottom Side (lower)Front Valance Molding Drawer Side Drawer Back Drawer Bottom Drawer Front Drawer Guide Knob Size 3/4" x 2" x 22" 1/4" x 8" x 26-5/8" 3/4" x 2-1/2" x 26-5/8" see Table 1 see Table 1 see Table 1 see Table 1 see Table 1 3/4" x 2" x 4" 3/4" x 2-1/4" x 4" 3/8" x 3" x 7-1/2" 1/4" x 1/4" round 1/4" x 4" x 4-1/2" 1/4" x 4" x 5-3/4" 1/4" x 4-1/4" x 5-3/4" 3/4" x 4" x 6" 1/8" x 3/4" x 4-1/4" see Figure 11Number Required 2 2 1 1 1 1 1 1 2 2 1 12 in. 2 1 1 1 3 1

Corner Shelf Complete Schematic

Corner Shelf Instructions
Step 1: Cut the Two Sides (A) and Two Back Pieces (B) 1. Cut the two side pine pieces (A) according to the specified dimensions. 2. Use the dado-head to cut the shelf grooves and ends at a 6-degree angle on both side pieces (A) (see Figure 1). 3. Choose the wood from which youwould like to cut the back pieces (B): scrap wall paneling or 1/4" plywood are two possibilities. 4. Measure the actual thickness of the wood for the back pieces (B). 5. Make a rabbet the thickness of the back pieces x 3/8" along the back edges of the side pieces (A) (see Figure 2) to accept the back pieces (B). 6. Cut the two back pieces according to the specified dimensions.

Figure 1: SidePieces (A) Detailed Layout

Figure 2: Side Pieces (A) Rabbet

Step 2: Cut the Back Support (C) 1. Cut the back support (C) according to the specified dimensions. 2. Mark the back support (C) according to the dado layout in Figure 3. 3. Use the dado-head to cut the dadoes. 4. Reset the dado-head to equal the thickness of the back pieces (B). 5. Incline the blade to 45 degrees. 6. Make the 1/2"cut to accept the back pieces (B) (see Figure 4). 7. Set the blade at 45 degrees again. 8. Rip the waste away from the back support (C) (see Figure 5). 9. Rip the waste away.

Figure 4: Making the 1/2" Cut in the Back Support (C) to Accept the Back Pieces (B)

Figure 5: Trimming the Back Support (C) Waste

Figure 3: Back Support (C) Dado Layout

Step 3: Cut the Shelves 1. Cut the top piece(D), top shelf (E), middle shelf (F), lower shelf (G) and bottom piece (H) to the shape shown in Figure 6 using the dimensions listed in Table 1. NOTE: The bottom piece (H) has the same front and side profile as the bottom shelf, BUT extends under the back support (C). 2. Notch the lower shelf (G) to fit around the back pieces (B).

Figure 6: Shape of Top Piece (D), Shelves (E, F, G, and BottomPiece (H)

Table 1. Top Piece (D), Shelves (E, F, G,) and Bottom Piece Dimensions
A Top (D) Top Shelf (E) Middle Shelf (F) Lower Shelf (G) Bottom (H) 8-1/2" 7-5/16" 8-3/8" 10-5/8" 10-5/8" B 2-1/2" 2" 2" 2-1/4" 2-1/4" C 7-3/4" 6-3/8" 7-1/8" 8-5/8" 9" D 1" 1-1/8" 1-1/8" 1-1/8" 1"

Step 4: Cut the Lower Sides (I) and Front Parts (J) 1. Cut the lower sides (I) according to the specifieddimensions. 2. Make a rabbet the thickness of the back pieces x 3/8" along the back edges of the lower sides (I) (see Figure 7) to accept the back pieces (B). 3. Miter the front edges of the lower sides (I) at 22-1/2 degrees to meet the front parts (J) (see Figure 8). 4. Cut the front parts (J) according to the specified dimensions. 5. Miter the outside edges of the front parts (J) at 22-1/2 degrees tomeet the lower sides (I) (see Figure 8).

Figure 7: Lower Sides (I) Rabbet

Figure 8: Mitering the Lower Sides (I) and Front Parts (J)

Step 5: Assemble 1. Test assemble the parts that you have cut so far. 2. Adjust any parts that do not fit properly. 3. Use glue and brads to make the final assemble. Step 6: Cut and Fit the Valance (K) 1. Select a 3/8" x 3-1/4" x 6" piece of stock. 2. Set...