Sony gnx 600 manual de servicio

HCD-GNX600
SERVICE MANUAL
Ver. 1.2 2007.12

E Model Australian Model

• HCD-GNX600 is the Amplifier, CD player, tape deck and tuner section in MHC-GNX600.

Model Name Using Similar Mechanism CD Section CD Mechanism Type Base Unit Name Optical Pick-up Name TAPE Section Model Name Using Similar Mechanism Tape Transport Mechanism Type

HCD-GNX800 CDM74KFS-F1BD81A BU-F1BD81A KSM-215DCP/C2NPHCD-GNX800 CWN42FF601

SPECIFICATIONS
Amplifier section The following are measured at 120 V, 220 V, 240 V AC, 50/60 Hz Front speakers DIN power output (rated) 130 + 130 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 160 + 160 watts(6 ohms at 1 kHz, 10% THD) Sub woofer Continuous RMS power output (reference) 200 watts (4 ohms at 100 Hz, 10% THD) TV (AUDIO) IN (phono jack)voltage 250 mV, impedance 47 kiloohms MIC (phone jack) sensitivity 1 mV, impedance 10 kiloohms Outputs PHONES (stereo mini jack) accepts headphones of 8 ohms or more FRONT SPEAKER/SUB WOOFER OUT Use only the supplied speaker Disc player section System Laser

Laser Output

Frequency response Wave length Signal-to-noise ratio Dynamic range Tape deck section Recording system Frequency responseCompact disc and digital audio system Semiconductor laser (λ=780 nm) Emission duration: continuous Max. 44.6 µW* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture. 2 Hz – 20 kHz (±0.5 dB) 780 – 790 nm More than 90 dB More than 90 dB

4-track 2-channel stereo 50 – 13,000 Hz (±3 dB), using Sony TYPE I tape –Continued on next page –

MINI HI-FI COMPONENT SYSTEM
9-887-199-03
2007L02-1 © 2007.12

Sony Corporation
Audio Business Group Published by Sony Techno Create Corporation

HCD-GNX600

Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range 87.5 – 108.0 MHz Antenna FM lead antenna Antenna terminals 75 ohm unbalanced Intermediate frequency 10.7 MHz AM tunersection Tuning range Latin American models: 530 – 1,710 kHz (with the interval set at 10 kHz) 531 – 1,710 kHz (with the interval set at 9 kHz) Other models: 531 – 1,602 kHz (with the interval set at 9 kHz) 530 – 1,710 kHz (with the interval set at 10 kHz) Antenna AM loop antenna Antenna terminals External antenna terminal Intermediate frequency 450 kHz General Power requirements Australian model:Argentina model: Other models:

Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of soldering iron around 270˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Becareful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Power consumption Dimensions (w/h/d) (Approx.) Mass (Approx.) Supplied accessories:

230 – 240 V AC, 50/60 Hz 220 V AC, 50/60 Hz 120 V or 220 – 240 V AC, 50/60 Hz Adjustable withvoltage selector 110 watts 280 × 326 × 385.5 mm 6.3 kg Remote Commander (1) Batteries (2) AM loop antenna (1) FM lead antenna (1) Front speaker pads (8) Sub woofer pads (4)

This appliance is classified as a CLASS 1 LASER product. This label is located on the rear exterior.

Unleaded solder Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the soldercontains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)

Design and specifications are subject to change without notice.

: LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron...